HELP with setup for Atomik arc 58 cat

[Mr.Joshua]

It doesn't say that works with swordfish 300A

[flraptor07]

It does, I use it on both of my 300s.

[Mr.Joshua]

Ran the boat again today for 4min brought it in checked temp 120deg.Seems like the x450 prop is the right one😃GPS recorded top speed 52mph.
But I still can't pull any data from the logger or even access the parameters

[flraptor07]

Ran the boat again today for 4min brought it in checked temp 120deg.Seems like the x450 prop is the right one��GPS recorded top speed 52mph.
But I still can't pull any data from the logger or even access the parameters

Joshua,
There was a member on here not too long ago that had the same problem and he had to get a firmware update or something like that, let me see if I can find it for you.

[flraptor07]

Look here posts 260 and 263 http://forums.offshoreelectrics.com/...s-Scarab/page9 Contact Hifei for update I think he said Michelle.

[Mr.Joshua]

Thanks buddy you have been a big help. There is some firmware update that the ESC needs. I found it on hifei web site but it's not getting to the ESC. I'm waiting to hear back from Michelle on how to hopefully solve issue

[Mr.Joshua]

ESC firmware upgraded and the boat is a rocketimage.jpgi haven't had this much fun in a whileimage.jpg

[flraptor07]

ESC firmware upgraded and the boat is a rocket[ATTACH=CONFIG]122118[/ATTACH]i haven't had this much fun in a while[ATTACH=CONFIG]122119[/ATTACH]

That's great Joshua, I'm glad you got it figured out, almost 60mph is flying for that big of a boat! Those big boats look really cool on the water at that speed, my Vern Kilmer Viper 48 runs almost 65 and it's a blast to drive.

[HangTheMan]

If you are still having troubles uploading the data or are getting errors trying to upload the data, make sure the program is ran in administrator mode. To do this right click on the icon and choose "Run as Adminstrator"

[Mr.Joshua]

Good thing I was able to get that update and access my parameters the LVC was set at 2.5v per cell.That could have been bad. I set it 3.2v per cell but my run time was like cut in half .Why is that? And when I turn my boat on it beeps twice followed by 10 beeps? Shouldn't it only beep 8 times for 8s?

[paDDY]

Man that cat is really moving at almost 60. Must be a blast.

[flraptor07]

Good thing I was able to get that update and access my parameters the LVC was set at 2.5v per cell.That could have been bad. I set it 3.2v per cell but my run time was like cut in half .Why is that? And when I turn my boat on it beeps twice followed by 10 beeps? Shouldn't it only beep 8 times for 8s?

I run my LVC @ 3.0 on all my boats and I've never had a issue. The reason you lose run time with the higher LVC setting is it shuts down @ 3.2 volts per cell instead of 2.5, if you lower it to 3.0 you'll pick up some of your run time. Yes it should beep 8 times if it's set for 8s sometimes if you have it set on auto it won't pick up the cell count for some reason. I always set mine manually for whatever cell count I'm using.

[Mr.Joshua]

Ok so I should set it to 3.0v LVC? Then set it at 8s? What about PMW Rate ? Mine is at 8 KHz. Timing advance is set at auto

[flraptor07]

Ok so I should set it to 3.0v LVC? Then set it at 8s? What about PMW Rate ? Mine is at 8 KHz. Timing advance is set at auto

Yes on all except timing, I also set that manual set it @ about 5deg and check temps. You can go up till temp starts going up then stop and maybe back it up a couple deg.

[Mr.Joshua]

If timing advance is set to auto. What does it do?