BBY's HRP 06 build

[RandyatBBY]

I got a little more done yesterday I mounted the motors. I will be settting up the stuffing tubes and mounts today. I decided to use CF plate for the housings.


Uploaded with ImageShack.us

[johnnyhpr06]

how about the water pickups any progress there, looks like were almost there.

[RandyatBBY]

I finished the stuffing tubes yesterday and cut the holes for the water pick up. I will install the pickups today. I also ordered the tees and the outlets yesterday. I have taken some pictures but my back up computer does not have the ability to process the pictures. After I get my regular computer back I will post some pictures.

[johnnyhpr06]

looks good ,i was real busy last time you called ,we didnt get a chance to talk about cowl locks

[RandyatBBY]

looks good ,i was real busy last time you called ,we didnt get a chance to talk about cowl locks

No Problem I was wondering. But I have had a lot of other things to do. I just got the water pickups fitted, I have been at it a little today I also got the outlets in today thinking about ware to put them. I ned to glue the pickups in first.

[RandyatBBY]

Update on the pictures. I got a little behind loading pictures while my computer was in the shop getting the virus removed. But now it is fixed and I am back at it.





I should have dusted/vacuumed it off before I took the picture


Uploaded with ImageShack.us

[RandyatBBY]

I got the water pickups installed and glued. I used Loctite 9462 Hysol adhesive on this build, good to know if you are installing threw hull application. It needs to sit for 24hr to cure.

[bonewar]

Update on the pictures. I got a little behind loading pictures while my computer was in the shop getting the virus removed. But now it is fixed and I am back at it.





I should have dusted/vacuumed it off before I took the picture


Uploaded with ImageShack.us

Randy,

Can you please explain what the extra brass tubing is for on the stuffing tube.

I really need a good oiling idea for my M12 project.

Would love to no how you go about making yours.

Thanks mate.

Bye the way very nice build .

Bonewar

[JohnZ]

Absolutely fabulous, Randy! Is this a glass or ABS hull?
What hardware are you using? I've never seen these before.
BTW I polished the ride stabilisers and turn fins on my O.M. 26, they look pretty good. I used my Dremel and a number of polishing pads. The polishing compound was Mothers Aluminum Polish.

[RandyatBBY]

Randy,

Can you please explain what the extra brass tubing is for on the stuffing tube.

I really need a good oiling idea for my M12 project.

Would love to no how you go about making yours.

Thanks mate.

Bye the way very nice build .

Bonewar

There is no Teflon tubing in this stuffing tube. It is double layer brass tubing then it is Hard soldered on both ends. then the extra tube is soldered and drilled. I use a mix Slick 50 and STP pumped in to the reservoir.

[RandyatBBY]

Absolutely fabulous, Randy! Is this a glass or ABS hull?
What hardware are you using? I've never seen these before.
BTW I polished the ride stabilisers and turn fins on my O.M. 26, they look pretty good. I used my Dremel and a number of polishing pads. The polishing compound was Mothers Aluminum Polish.

It is a swiss made boat CF/Kev hull, Link below
http://www.swissmodelpowerboatteam.ch/index_en.htm

[RandyatBBY]

I came in to the shop today to get a little done on my Oiler built the basic holder for the distribution center. Hear is what I got done today The sink is plug ed up and I need to fix it so no more today on this project.


Uploaded with ImageShack.us

[johnnyhpr06]

never seen this type of oiler system ,i'm likeing the way it looks though ,is it gravity fed or pumped in ?

[RandyatBBY]

never seen this type of oiler system ,i'm likeing the way it looks though ,is it gravity fed or pumped in ?

It will be a leach system, There will be a pump to fill the tank and prime. I have been testing with several designs over the last couple of years.

[RandyatBBY]

Getting ready to mount the oiler.


Uploaded with ImageShack.us