I am looking for a good setup Deltaforce 33 " cyberstorm.

[madmikepags]

37,000 isn't crazy but if you are gonna run it on a mono make sure you use a wet well or cool the stuffing tube inside the boat, at those RPMs, the tube and thaft get very hot and the brass tube will melt.

[madmikepags]

Hey SSchevy , while the Lehner motors are very high quality units I personally have found that you can get better efficiency from other brands at cheaper prices, I don't know if you're here in the states but Neu's Leopards and others are much cheaper here in the states.

[lenny]

HK has some good cheap motors,
PM for you mike on motors for a pursuit.
So not to take over the OP post,
Or I my just put up a post for info.

[SSchevy98]

What do you mean by that?

[madmikepags]

SS who are you asking???

[SSchevy98]

SS who are you asking???

Lenny.

What do you think TP power 4092 1600 kv motor + 6-8s lipo ?

[SSchevy98]

HK has some good cheap motors,
PM for you mike on motors for a pursuit.
So not to take over the OP post,
Or I my just put up a post for info.

What do you mean by that?

[lenny]

I did not want to get off of the info you where looking for,
So I sent a pm to Mike for some input on my pursuit and setup for it.

I have a pursuit mono and running a 4074 1800kv in it,
And I was asking Mike for some info on a better motor setup.
Because I have a lot of motors setting around to try in it,
Now that I see how the boat runs and handles I think it's time to up grade a little.

[lenny]

My buddy is using one of these motors in a geico on 6s with a 130a hv seaking esc,
Runs nice and cool and lots of power and head room for the amps to.
http://www.hobbyking.com/hobbyking/s..._Inrunner.html

May be one of these motors would get things rolling for you,
To test and see how the setup work in that hull.
http://www.hobbyking.com/hobbyking/s..._Inrunner.html
http://www.hobbyking.com/hobbyking/s..._Inrunner.html

[SSchevy98]

My buddy is using one of these motors in a geico on 6s with a 130a hv seaking esc,
Runs nice and cool and lots of power and head room for the amps to.
http://www.hobbyking.com/hobbyking/s..._Inrunner.html

May be one of these motors would get things rolling for you,
To test and see how the setup work in that hull.
http://www.hobbyking.com/hobbyking/s..._Inrunner.html
http://www.hobbyking.com/hobbyking/s..._Inrunner.html

I have already leopard 4082 1250 kv motor

[lenny]

I think you would be push the limits of the motor on 6s,

22.2 * 1600 = 35520 rpm unloaded.

You need to make a choice to run on 6s or 8s than we can help find a motor for you.

Lenny.

What do you think TP power 4092 1600 kv motor + 6-8s lipo ?

[lenny]

Well on 8s that would pushing it some at 1250 *29.6 = 37000 rpm unloaded.
But 6s and 7s would be good, 1250*22.2=27750 rpm and 1250*25.9=32375 rpm.
That is a lot of motor for that hull.

[SSchevy98]

It is then seen how that works.

[Brushless55]

I think you would be push the limits of the motor on 6s,

22.2 * 1600 = 35520 rpm unloaded.

You need to make a choice to run on 6s or 8s than we can help find a motor for you.

yes...

[SSchevy98]

8s.

Are those TP pro force 4s 6600 70C batteries too heavy delta force 33 cyberstorm?


676 grams?