Help me to choose a motor for this hull

[jujux1]

Tu n" as rien d' autre a faire ptit branleur?
Si tu as quelque chose a dire je t' ecoute point barre. Tu es quand meme une belle langue de pute. Il vaut mieux qu' on ne se croise pas...
Fais ta vie vieille mégère, tu es pourri de l' intérieur, je n' ai jamais vu ca...

This guy is jealous, stupid. Why do you have to talk about me? If you have something to say talk to me. Are you a man or what?

Et si vous vous croisez, il se passe quoi ? tu lui pretes ta radio dans laquelle il n'y a meme pas de pile !
Pourri de l'intérieur, tu parles de toi, c'est ça ?
Akula is not a jalous guy, look at this http://www.offshore-rc.com/forum/ind...=8#entry565320

His boat have tasted some water, but yours ??

[znus]

Hull is a RCMK Flying Cat...and right now it's missing its hatch

Motors are SSS 4092 2140 kv d-winds. I shortened the shaft about 5-7 mm (along with the extra 5 mm alu plate just beneath the motors) to make them fit. Didn't wanna shorten the motorshaft past the grub/drive dog "area".

ESC's are T180's

Lipos are four 4S 5000 mAh 20C. It needs a lot off weight in the nose, which all in all makes it pretty steady on choppy water.

Props are TJM 40/3 in the videos, which are the preimer runs (about a month ago)

IMAG0053_zps94317761.jpg

IMAG0056-1_zpsb1f9aaf6.jpg

IMAG0057_zpsa3ad3692.jpg

IMAG0058_zpsf1236d20.jpg

[kendt]

Shwing!!!

[J.W. Pepper]

That thing is SICK!!! Dang I think its giving me wood.

That thing is SICK!!! -- Agreed, that is one very nice setup

[Alfa Spirit]

HOR outboard motor mount is very well made





If you want to use a high RPM and high Power motor like Turniçy http://www.hobbyking.com/hobbycity/s...dProduct=11183, there is enough place to use a collet 6mm/ 4,75mm

[Alfa Spirit]

I use the HOR outboards. Two of them!



The flexshaft is 3/16" with squares at both ends, and the propshaft is 3/16 with 4 mm thread.
If you wanna run bigger props you just raise the cavitation plate with washers.



Just be really picky about lubeing the shafts after every session! You can see my oil can-mod in the pictures above

Hi,

What setup are you running? How many RPM maxi unload?

I have a set of Turnigy class 600 1900kV and 2000 Watts continious.

I will use one outrunner motor with 5S battery, 35000 RPM unload. The problem is motor" s shaft diameter : 6mm., with 3/16" square end flex shaft and 6mm motor shaft to 3/16" flex shaft it will work,

[akula]

Hull is a RCMK Flying Cat...and right now it's missing its hatch

Motors are SSS 4092 2140 kv d-winds. I shortened the shaft about 5-7 mm (along with the extra 5 mm alu plate just beneath the motors) to make them fit. Didn't wanna shorten the motorshaft past the grub/drive dog "area".

ESC's are T180's

Lipos are four 4S 5000 mAh 20C. It needs a lot off weight in the nose, which all in all makes it pretty steady on choppy water.

Props are TJM 40/3 in the videos, which are the preimer runs (about a month ago)

Alfa, have you entirelly read the Znus' post ???

Ok, so I will explain for the newbie you are

The motors are 40mm diameter x 92mm long. and inrunner (SSS 4092 is not a secret code, just the name with the specs).
The 2140Kv used in 4S 5000mAh means that unload, the motors run at 2140 x 4 x 3.7V = 31672rpm
Propellers are 40mm diameter and 3 blades.

ESC T180 probably means that the Electronic speed controllers are Turnigy 180A.


You're welcome...

regards.

Francois

[Alfa Spirit]

Those are big motors with high RPM for an outboard motor mount. I had the Turnigy H37-36 before buying the HOR outboard I didn' t noticed shaft diameter but that will work with a 6mm / 4,75mm collet and flex shaft square end for rthe propeller side.

[Southwest]

Isn't this the person who sent pictures thru his lips saying f*** you! Should be banned as he is wasting Steve V. site space. People have by passed this thread cause of this BIRD!

[Alfa Spirit]

Sorru, what are you trying to say? I don' t understand.

@ ZNUS : How is the totation of propellers on your twin outboard? Thanks

[Alfa Spirit]

Sorru, what are you trying to say? I don' t understand.

@ ZNUS : How is the totation of propellers on your twin outboard? Thanks

[znus]

Sorru, what are you trying to say? I don' t understand.

@ ZNUS : How is the totation of propellers on your twin outboard? Thanks

Alfa. Right now I run both motors in normal rotation. I do have counter rotating flexshafts but I haven't installed them yet.
Right now one motor is on the workbench and I'm waiting for a new brass bushing and propshaft. Must have gotten som dirt (sand) in there because it just "stuck" and took the flexshaft with it in the fall.

Check 00:54. That's one propshaft almost welding itself to the brass bushing. I had to torch and knock the propshaft out with a hammer.

Did you know there's an european TFL (HOR)? http://www.tfl-hobby.de/

[Alfa Spirit]

MTC have high quality flex shafts but they say 5mm diameter and we need square end 4mm x 4 mm https://www.mtc-powerboat.de/index.p...1&variante=193

I bought Dave Marles flex shaft "Prestwich models" and collet for 6mm motor shaft

[Alfa Spirit]

Scorpion are very good but the 3026- 1900kV is too small, not enough Watts. I installed a Turnigy H3736-1970kV

http://www.hobbyking.com/hobbyking/s...trsearch=h3736

The motor shaft is 6mm diameter so I use a 3/16" flex shaft with square end for propeller shatt and a collet 6mm ==> 3/16" for motor shaft, there is enough place in motor mount fot a collet.

[Alfa Spirit]

I found the motor for the Lap Car.

Size is 4274, 4 poles 2000kV for 5S battery. 120A Seaking shouk bz znough?