Genesis catamaran ???

[justintime2w8]

Three emails back and forth and I could not pry dimensions out of them.
You will find my post on here last week begging someone for them.
If those work, $375 and you will have super scale drives and rudder.

[tiqueman]

I was just looking at them.. Im not convinced theyd work yet. I wonder why they wont talk?

[justintime2w8]

Yea seems like critical info for for someone attempting to purchase their stuff. My neu's and turnigy 180's are sitting here waiting for a home....

[tiqueman]

Yea seems like critical info for for someone attempting to purchase their stuff. My neu's and turnigy 180's are sitting here waiting for a home....

Haha.. Nice

Yeah youd think theyd share... wierd

[FighterCat57]

I have one of those on a mini rio. Those are waay too small. For micro set ups.

Ooops. They looked like they would fit the transom space. Not much space!
Isn't 3mm the same size drive at the KOS uses in it's twin setup? (I guess that is too small! )
________
DRUIDISM FORUM

[Alfa Spirit]

Are you talking about this model?

http://www.toughracing.com/zc126d/index.php?main_page=product_info&cPath=11_17&products_id=1313

[Alfa Spirit]

If I don' t find long stingers I' ll build something like this. Motor ==> flex collet ==> flex shaft ==> flex collet ==> shaft with sterntube

[Jeff Wohlt]

That will work fine....even a little neg angle will not hurt it a bit.

[steveo]

if anybody is going twins maybe try the twin drives hotr offers from there twin boat

[tiqueman]

if anybody is going twins maybe try the twin drives hotr offers from there twin boat

too small

[justintime2w8]

Way too short, there is not enough height clearance for the props. Need to get them past the transom, about 3 3/4 in. total.

[FighterCat57]

How about using a two bolt strut with wire drives? They are smaller struts, but the wire drives will strengthen the cable setup for more power in less tube space. Jeff makes the wire drives for the 4mm prop shaft. I have a pair in the EKOS.

http://cgi.ebay.com/aluminum-strut-1-8-shaft-full-set-/280428893152?cmd=ViewItem&pt=Radio_Control_Vehicles&hash=item414add53e0#ht_2492wt_911

Just a thought.
________
Sc2 Replays

[tiqueman]

How about using a two bolt strut with wire drives? They are smaller struts, but the wire drives will strengthen the cable setup for more power in less tube space. Jeff makes the wire drives for the 4mm prop shaft. I have a pair in the EKOS.

http://cgi.ebay.com/aluminum-strut-1-8-shaft-full-set-/280428893152?cmd=ViewItem&pt=Radio_Control_Vehicles&hash=item414add53e0#ht_2492wt_911

Just a thought.

Those are 1.25" long. That would be an awful lot of unsupported shaft to get out to the transom. And as Justin said, you have to get out that far so the props clear the overhang.

[FighterCat57]

Those are 1.25" long. That would be an awful lot of unsupported shaft to get out to the transom. And as Justin said, you have to get out that far so the props clear the overhang.

I was actually thinking transom mounted, not sponson transom mounted. Run the tube out of the sponson transom and to the transom mounted strut hanger. Since there is enough space on the transom for these smaller strut mounts.

Again, just a thought, but don't see why it wouldn't work.
________
Gm foods

[tiqueman]

Gotcha... it could possibly work. Just looking at it again... it may do it.