Experience with a Turnigy T5692 1320KV motor???

[Mel279]

Magus

you don't have to get lehner motor to reach 80-90mph, with those cheap motor you can get to that speed

[JIM MARCUM]

That's one bad assed cat! With that setup you'e gonna need a bigger lake. With that much power & speed potential be sure to take the time to trim your cat out so it runs as flat as possible. A blowover crash at that speed could, and probably would, rip the hull apart & send all your hard work to the lake bottom. Would be a good idea to have a recovery boat & SCUBA diver on hand to drop a location bouy where it goes down.

Unless you plan on going for a new T Offshore class SAW record, I'd stay with 8S2P and just have fun, & getting experience driving that monster cat. NAMBA S & T Offshore SAW classes are limited to 8S2p and 10S2P respectfully. If you can get that puppy to run 100MPH on 8S, 110MPH on 10S, you should save up you money & fly to LA in October for the NAMBA Legg Lake SAW races. JIM

[ray schrauwen]

I plan on putting a 5692 1000kv in my DF41 on 8s. HK are out of stock though as usual. These sold out fast. Funny how they still have stock of the 5682 version but the 92 version says 1500 more watts of power.

Just a secret note: If you have a certain item in your cart at HK and it goes on B/O, you can complete the order for the price today and wait for stock to arrive. I can almost garantee you if they re-stock the price will increase. You might be waiting a while though...

I have a Cart with 2-1050 kv motor in there. Thinking of pushing the button if need be soon.

If I try hard I can squeeze'm into my 41" Fantasm twin cat, lol...

[ray schrauwen]

I'm going to run a 1320 in my 40" mono on 6S2P and also, try the 780KV motor I have on 8S+++ ?

I have never heard from a definative source that they are 6 pole motors but, maybe they are??

[ray schrauwen]

Timo Heinrichs setup: LMT 3040/6 (diameter 60mm / length: 80mm / 1750kv ) and Schulze 333WK
My problem: The Lehners and the HV esc are to expensive

...

Lehners yes b ut, Fightercat sells nice esc's that will work well for you and less expensive.

[oscarel]

I'm going to run a 1320 in my 40" mono on 6S2P and also, try the 780KV motor I have on 8S+++ ?

I have never heard from a definative source that they are 6 pole motors but, maybe they are??

If I set the Castle software to show 4 pole motor it reads 35K loaded rpm with 6s, if set to 6 pole it shows 23.5 which should be about right.

[Old Sloppy]

My problem: The Lehners and the HV esc are to expensive

The Lehners and the HV esc are "too" expensive.

I disagree..

Harry

[Drax21]

Just a secret note: If you have a certain item in your cart at HK and it goes on B/O, you can complete the order for the price today and wait for stock to arrive. I can almost garantee you if they re-stock the price will increase. You might be waiting a while though...

I have a Cart with 2-1050 kv motor in there. Thinking of pushing the button if need be soon.

If I try hard I can squeeze'm into my 41" Fantasm twin cat, lol...

Thanks for the tip.

[Drax21]

Hey Ray I tried to add to cart but HK won't let me and I guess I know why. Price increase coming..... Wish I started this project earlier.

[RCKong]

I have a Cart with 2-1050 kv motor in there. Thinking of pushing the button if need be soon.

If I try hard I can squeeze'm into my 41" Fantasm twin cat, lol...

Ray, 2 1520's on 6's will get you in the 80mph range without all the extra weight. 8s probably around 90 - 100mph no joke. That is what I'm doin with my Fantasm... 4sure

[ray schrauwen]

Hey Ray I tried to add to cart but HK won't let me and I guess I know why. Price increase coming..... Wish I started this project earlier.

No problem. Yes, once on B/O you cannot add to cart but if you have them in your cart as the item goes to BO then you cAn still order them & wait. I don't really have the coin to BO a pair but, I might. I can increase the BO quantity though at this time.

[ray schrauwen]

Well if you would sell me a pair of 1520's for $60 each (original sale price) I'll take a pair! lol... Kidding.

I think I'll stay with 880Kv T600 outrunners I have on 9S up. or other O/R motors for $40 a pop or so. They sound cool.

[ray schrauwen]

If I set the Castle software to show 4 pole motor it reads 35K loaded rpm with 6s, if set to 6 pole it shows 23.5 which should be about right.

I'm not sure how to interpret what you are saying with these numbers. Can you elaborate?


Forget it, I get it now, 22.2 x 1320= ~29,000rpm unloaded = about 23,000 loaded or so.

What would a good 6 lap prop be on 6S?

[oscarel]

I'm not sure how to interpret what you are saying with these numbers. Can you elaborate?


Forget it, I get it now, 22.2 x 1320= ~29,000rpm unloaded = about 23,000 loaded or so.

What would a good 6 lap prop be on 6S?

Yep, you got it. Here's the charts, first is set to 4 pole, second to 6 pole.

4 pole.jpg6 pole.jpg

[Magus]

Okay, I've ordered two 5692 for the epv 135.
So I hooe, that they will fast be restocked and delivered to me...
And than 6S and YEAH

6S = 22,2 V = ~ 29.000rpm
9S = 33,3 V = ~ 40.000rpm
12S = 44,4V = ~ 58.000rpm

So the max will be 9S

Greets,
Birger