MHZ Lizard Xtreme

[cacofonix]

ok ok thanks for your help
in stock i have : K45 / X445 (original) / X445 (mod) / X447 (raw ....) / K48 / K51

i think the good one is in the list !!

H

[focused]

just uploaded two vids to youtube .

vid 1 Lizard in action taken in slow-motion it was very very windy to much for FE.

http://www.youtube.com/watch?v=MDPRk-ZDhkg

vid 2 testing the lizard first run and a second for the h&m x-ray L we did not go full throttle yet .

http://www.youtube.com/watch?v=eygZ_2vOg_I

Michiel.

[cacofonix]

great !!

one question about stinger position, on transom how many millimeters from the V bottom is the hole ??

H

[EPower]

great !!

one question about stinger position, on transom how many millimeters from the V bottom is the hole ??

H

Just put it as low as you possibly can

[focused]

great !!

one question about stinger position, on transom how many millimeters from the V bottom is the hole ??

H

Are you going to use the MHZ Trimax or some other strut because it depents on the type strut/stinger etc.



Michiel.

[cacofonix]

i use home made stinger , i have a lathe and milling machine .......
stinger length (from transom to DD) is 85 mm

[focused]

i use home made stinger , i have a lathe and milling machine .......
stinger length (from transom to DD) is 85 mm

Will it be adjustable ? i will measure my setup tomorrow from bottom to centre shaft.


Michiel.

[cacofonix]

only angle can be adjust

[EPower]

only angle can be adjust

that is all you need, changing angle will push the bow of the boat up or down
i was going to use the trimax in my boat but after taking a good look at it i opted for the stinger
1: it would allow me to have my shaft as low as possible
2: it also let's me run smaller props and that gives me less prop walk
as you can see in the vid of my boat it run's straight and fast with no bad habits I will take some more video this weekend running my new Hyperion 35c batt

Just take a look at the trimax setup and you should see what i mean
that's my two cent worth

[cacofonix]

hi folks

i test it last WE, i really enjoy this hull, much fun !!
but one problem : the brand new feigao 12Xl burnt after 4 run ......
it was with a X445 mod.

another point, very difficult to reach max speed : a lot of rolling
do you think that adding 2 turn fine will help ???

thanks

herve

[Flying Scotsman]

A 12XL and 6S are borderline on a X445...modified? and was the boat running wet? Were the 4 runs on the same day and what were the temperatures and what was the CG?

Douggie

[cacofonix]

yes a modified x445, K48 was ok, but with the modified X445 it was .......awesome

when motor burnt, T° were:
motor :185° with smoke
ESC : 122°
LIPO : 95°

motor stop after 7 minutes.

thanks

herve

[Flying Scotsman]

It looks like you just had too many volts to the motor.

Douggie

[cacofonix]

anyway, motor is dead
just to check, on this motor i change ball bearing with boca bearing sell by steven
to me, when i turn motor by hand it's much more harder than with original BB.....

hopefully a friend of mine had a motor to lent me, an outrunner a KD600L.
it fit very well in the hull !!!!

but i still have rolling problem ..

herve

[Flying Scotsman]

It sounds like you installed the bearings incorrectly. Show us a picture of the transom hardware

Douggie