MHZ Lizard Xtreme

[SJFE]

Got it...Getting it...Thanking you for it

[goldendesign04]

douggie,
as I usually see from one such as your self, clean an profesional.
I like it a lot, good work.
-Wayne

[Flying Scotsman]

Finished MHZ Xtreme Lizard

Thanks Wayne.
Finished Hull
Speedmaster hardware, 11XL Feaigo, Sentilon HV 100 esc, 1 5000 TP 3S and 1 5000 TP 2S in series, Y537/3 prop, Hitec HS 645MG servo.

[Steakhouse]

Thanks Wayne.
Finished Hull
Speedmaster hardware, 11XL Feaigo, Sentilon HV 100 esc, 1 5000 TP 3S and 1 5000 TP 2S in series, Y537 prop, Hitec HS 645MG servo.

Very clean setup. Nice!

[bababoboRc]

MHZ Lizard

Hi There Flying Scotsman i love your boat
i'm setting up the same hull and similar setup, and speed controller
but i have this motor Turnigy BL 36-56-2700 running on 6S Lithium, is this powerplant too small for this size hull ?
and what size rudder and surface drive are you running

Regards
Adrian

[Flying Scotsman]

I am not familliar with that motor and It looks like a small can. I presume 2700kv. If that is the case WAY TOO HOT with 6S . What prop ?
The hardware is Speedmaster as previously noted. Please note I am borderline on my setup

Product ID: ros-monosys
Speedmaster Mono Hardware System

Douggie

[SJFE]

I have to agree with Douggie. That motor is way to small and the kv rating is off the chart for your hull & voltage. Sorry.

[bababoboRc]

Thanks for the feedback guys
what motor would you recommend forthis hull, i want to use it as a sport boat but still want to get decent speed out of it
Douggie
i'm not surw what you mean by your setup is on borderline?
excuse my ignorance i'm new at this elecric stuff

Cheers
Adrian

is this the stinger ? .187 (3/16-inch Cable) for .21 - .40 motors

http://www.rossisales.com/strut.html

rudder ?.40 Rudder Assemblies

http://www.rossisales.com/ruddernew2.html

[Flying Scotsman]

Hi Adrian, when I say borderline the esc is rated for 100 amps and the 11XL motor is rated at 1500 rpm per Kv. I am using 5S LI-PO therefore nominal RPM= 27,000. The hull is 32.5" L and total weight is 5.3lbs. I am using a small diameter prop Y537/3 to limit the amperage draw...I hope!!!
This hull size and weight is more suited to a large can high torque motor...KB45 XL, Neu power or transmission with Feaigo power. This what I had sitting arround and I hope it does not go POOF.
I hope this helps.

Douggie

[bababoboRc]

Hi There
Thanks Douggie for your feedback i got my hull today looks good in white
i also took your advice and brought two motors
this one http://www.hobbycity.com/hobbycity/s...idProduct=4937
and this

http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=4936

will give these a run ,cheap motors really $ 53 each

Regards Adrian

[Flying Scotsman]

[QUOTE=bababoboRc;31890]Hi There
Thanks Douggie for your feedback i got my hull today looks good in white
i also took your advice and brought two motors
this one http://www.hobbycity.com/hobbycity/s...idProduct=4937
and this

http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=4936

will give these a run ,cheap motors really $ 53 each


Adrian, motors can be cheap, quality esc and motors NO!!! If you look at the power to bucs equation

[bababoboRc]

Hi there Douggie
Sorry to be a pain but i cannot find the rudder you are using on the speedmaster site is it a 21 mono rudder or the 40 rudder cheers
Adrian

[Flying Scotsman]

Hi there Douggie
Sorry to be a pain but i cannot find the rudder you are using on the speedmaster site is it a 21 mono rudder or the 40 rudder cheers
Adrian

No pain....21 but you may wish to lower the rudder as far as possible.
When you get the hang of it, there are many guys that can help you, with more experience than myself.

Enjoy your build.

Douggie

[bababoboRc]

Thanks for the help Douggie
i will put some pics as soon as i make a start on this build
Regards
Adrian

[bababoboRc]

Hi Douggie have you run your boat yet ??