Project Genesis!

[mudl]

Hello

before i planed to built the genesis twinn,i made some testes with the original setup.
I tested the genesis with a 40 graupner carbon prop with 3,than with 5 and last with 7s lipos.With 7s lipos it was very fast (about 55mph) but first the prop was broken,and after this the flex cabel was broken.
Maybe it runs with a better flexcable,a drive with ball bearings and a metal prop.
For the esc and the motor it was no problem.
Now with two scorpion 3026 and octura x447 i hope it runs about 75 mph

we will see

bye mudl

[blackcat26]

Hey Mudl what kv are those scorpions? And what voltage ya gonna run em on?

[mudl]

Hello

3026-1400 with 7s for both motors

mudl

[Alfa Spirit]

2x5S and 2000kV motors ??

Edit: reply at same time

[Brushless55]

Sweet looking build of a twin!
would a single 1515 2200kv on 4s work well in this hull?

[FighterCat57]

Not sure how a 1515 would do, but the 1527 is a monster. The hull actually twists about 25 degrees when the prop starts spinning!

[Brushless55]

Not sure how a 1515 would do, but the 1527 is a monster. The hull actually twists about 25 degrees when the prop starts spinning!

[FighterCat57]

I know, pretty cool, huh? I'll have to figure out a way to get some video of it soon! I'm running the 55/3 prop because the 57mm won't fit!

[Make-a-Wake]

A buddy of mine went to an x642 with the 1521 neu on 6s...........real close to 50, is what he said..........i think a tad faster...............

http://www.youtube.com/watch?v=8agAvTBTcEg

[FighterCat57]

A buddy of mine went to an x642 with the 1521 neu on 6s...........real close to 50.

http://www.youtube.com/watch?v=8agAvTBTcEg

Nice! I couldn't tell from the vid, but did it seem to pull to the right? I'm having a bit of a pull, but only at full throttle. It kind of twists and then steers right.

I now have a UBEC so I can go to 4s, 5s and even 6s. More to follow soon!

BTW- the shrink wrap over the strut/tube took care of the leak. That and the epoxy in the transom.

[Alfa Spirit]

Hello

new day,new pictures.



bye
mudl

This is a very nice job

I don' t understand the setup 7S for two combos esc+motor, right?

[Make-a-Wake]

Nice! I couldn't tell from the vid, but did it seem to pull to the right? I'm having a bit of a pull, but only at full throttle. It kind of twists and then steers right.

I now have a UBEC so I can go to 4s, 5s and even 6s. More to follow soon!

BTW- the shrink wrap over the strut/tube took care of the leak. That and the epoxy in the transom.

He's just mentioned a bit of torque roll out of the hole then nice and stable.

[FighterCat57]

He's just mentioned a bit of torque roll out of the hole then nice and stable.

Yeah, I get a bit of the torque roll too, but in the final 1/4 throttle there is a distinct 10-15 degree pull to the right. Perhaps I may have the strut set too low. It is about even with the bottom of the hull.

[rchippie]

I get the same torque roll you mentioned. I have my strut level with the bottom of the hull. I will have to modifiy to strut to get it higher.

[Alfa Spirit]

That' s why a twin setup is better with high power.
Depends of the hull, the Genesis Mystic isn' t very large
Have a look to this Falcon 41" single motor

http://www.youtube.com/watch?v=w1aJvJak30w