1/6 scale Jetsprint boats and 30mm Jet drives

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Mike Caruso
    Senior Member
    • May 2012
    • 940

    #31
    Originally posted by mickieb49
    Hi Guy's,
    Like what was previously mentioned, i will be using a 1800kv 4072 leopard motor with a 120 amp swordfish esc on 4s 5000Mah 40c battery, this setup has been good to me with no overheating or problems. That was with the Graupner units and Kehrer ( highly modified, see also my youtube vids)
    This unit like the tru Hamilton and Scott jets is not intended on trying to spin it over about the 25k mark, if you try to do that you will start getting a hydraulic locking effect and basically the effeciency will drop off. All too often i see people putting 4000kv motors into those NQD jet boats and running them on 3s and even 4s, then wonder why theu have problems?????
    This is a mixed flow pump and like Shaughnessy has said is a very different type of pump as compared to what is basically a propeller wrapped up in a inlet ( graupner and Kehrer)
    I will be trying lower kv motors but i believe the 1800kv to be the best.
    I am hoping to be able to share some more pictures of the new hulls very soon too.
    Here is my youtube link:

    Regards Mick
    Very cool slids sideways just like a river racer LOL
    Do It Like You Mean It .....or Don't Bother

    Comment

    • mickieb49
      Senior Member
      • May 2010
      • 237

      #32
      Hi guys, just thought an update was in order, sorry but no pictures yet. I will be getting the next last of trial injection molded parts sometime next week, providing it all lines up and fits together the full production of 1000 units will be in my hands within a week.
      As for the impellers, I had to change manufacturer, I have been ensured that I will have them in 3 weeks, I am using the same guy that made? The cnc roll bar clamps, i will try to get some pictures of what I have so far soon.
      The plans for the hull are finished so I should be routing out the mold for the vacuum mold in the next week or so, again I will update here with pictures once I have something to show.
      Again thank you everyone for their patience with me, trying to get this mammoth project off the ground whilst working full time and bringing 2 kids under the age of 2 is not easy.
      Regards mick

      Comment

      • TheShaughnessy
        Fast Electric Addict!
        • Mar 2011
        • 1431

        #33
        let me know when your ready for an order, pretty interested in trying one out.

        Comment

        • mickieb49
          Senior Member
          • May 2010
          • 237

          #34
          Hi Guy's, here is the rectified injection molded parts, pretty happy how they have turned up, just given the go ahead to manufacture 1000 units.
          The impellers should be finished in a week or so, because I had to change the manufacturer I could only get 200 made first, will post some pictures once I get them.
          On the hull side, I should be CNC'ing out the plug very soon.jet u.jpgjet unit.jpgjet unit1.jpgjet.jpg

          Comment

          • Mike Caruso
            Senior Member
            • May 2012
            • 940

            #35
            Looks first class.
            Do It Like You Mean It .....or Don't Bother

            Comment

            • rickwess
              Senior Member
              • Apr 2013
              • 777

              #36
              Very nice indeed. I can see myself getting one. Good for playing with in the shallower cottage waterfront. Much more dog friendly as well.

              Comment

              • TheShaughnessy
                Fast Electric Addict!
                • Mar 2011
                • 1431

                #37
                Figures, I get my stuff stolen and these are finally ready. Gonna have to put in some OT.

                Comment

                • mickieb49
                  Senior Member
                  • May 2010
                  • 237

                  #38
                  Originally posted by TheShaughnessy
                  Figures, I get my stuff stolen and these are finally ready. Gonna have to put in some OT.
                  I am thinking on selling the first few on a discounted rate , providing i get some Youtube footage of them.
                  Nearly got the smaller hull mold done, these will be Fiberglass, 450mm long. When i get the first one out of the mold i wil post some pictures.
                  Thanks for the feedback guy's, it is most appreciated.
                  Regards Mick

                  Comment

                  • Fella1340
                    Fast Electric Addict!
                    • May 2013
                    • 1035

                    #39
                    Looking forward seeing these available!

                    Comment

                    • mickieb49
                      Senior Member
                      • May 2010
                      • 237

                      #40
                      Hello all, I should have the jet units available in about 2 weeks, I should have all the injection molded parts on around the 21st, and the impellers around the following week. Will test one first, but all should be OK to sell some the week after , around 28th- 05th.
                      I am also going to put a few of these up for Christmas gifts.
                      Nearly finished the smaller hull mold, got a little wet sanding then polish before I can sell them, but hoping to have a few glass hull done before I release the jet unit.
                      Take care guys

                      Comment

                      • flraptor07
                        Fast Electric Addict!
                        • Aug 2013
                        • 2451

                        #41
                        How do you think these would work in a 36" or so cat hull twin setup? Might be fun

                        Comment

                        • mickieb49
                          Senior Member
                          • May 2010
                          • 237

                          #42
                          Originally posted by flraptor07
                          How do you think these would work in a 36" or so cat hull twin setup? Might be fun
                          Hi not too sure, I think it has been done before, went OK, as long as there is a 45_50mm flat section for the unit to mount to, it should go well.
                          Regards mick

                          Comment

                          • srislash
                            Not there yet
                            • Mar 2011
                            • 7673

                            #43
                            Keep up the good work Mickie.

                            Waiting for outcome

                            Comment

                            • daveives
                              Senior Member
                              • Jun 2009
                              • 109

                              #44
                              Please put me on the list for one.
                              Thanks
                              Dave Ives

                              Comment

                              • mickieb49
                                Senior Member
                                • May 2010
                                • 237

                                #45
                                Will do ,
                                Just received 4 big boxes of injection molded parts, all up just a shade over 7000 separate parts.
                                Also finished the small jetboat mold, am hoping to be pulling the first hull out in the coming days. I will document the whole build here as I do it, I will also be making a instruction sheet to put these units and hulls together.
                                You will also see in the pictures of the building amount of parts I am accumulating ready for the release, hopefully in the next week or so as the impellers should be finished by the 21st November, and posted to me sometime next week, the boxes for the jet units should be in my hot hands next week too, also should be getting close to having some video footage about the same period.
                                Providing I get the new router bits this week I should be CNCing out the plug for the bigger jetsprint hulls this weekend???
                                Warm regards all, and thankyou so much for not getting too bored with me trying to get it all together.
                                20131119_194252.jpg20131119_194257.jpg20131119_194337.jpg20131119_200812.jpg20131119_200825.jpg

                                Comment

                                Working...