Legg Lake 5-Day Super SAW Event Wed Nov 5th-Sun Nov 9th

[Darin Jordan]

Yep, I have a couple. Here is one.

View My Video

Thanks, Jay! That's cool!

[properchopper]

Did anyone at the event happen to capture any video of my N2-Cat making a run (successful run, preferably... :) )?

Still sorting ; found these 2 :

https://www.youtube.com/watch?v=YyAYCXzCfs0

https://www.youtube.com/watch?v=QIpqhagxjD8

[Darin Jordan]

Still sorting ; found these 2 :

https://www.youtube.com/watch?v=YyAYCXzCfs0

https://www.youtube.com/watch?v=QIpqhagxjD8

Perfect Tony... Thanks!

[properchopper]

(Still Sorting)

Andreas Lehner's Cat : I theenk this is a record run if you listen carefully at the end of the pass you can hear "There it is "

https://www.youtube.com/watch?v=PcaUAaIvRgE

[RaceMechaniX]

Here is a brief description of the T-hydro and some pics of the boat prior to the event.

The boat is my own design based loosely on the Raptor Rigger by Brian Buaas. The rudder assembly is from Chris Woods running a kitchen knife. The strut is from Lenny Blake at Rum Racing products with special bushings. 3/16" square drive system with flex cable, mostly Octura parts. I machined and broached my own motor couplers to adapt the 8mm shaft to square cable. Motor is a Lehner 22 series Hi-Amp. I will not say what exact wind or length used. Controller is a Schulze 40.160wk and I used a set of SLS V2 Magnum 10S 5Ah lipos. The prop is a stainless recasting from an existing two blade prop (I am not saying which one) that was cut down, profiled and thinned to a reasonable level but not too much so it had some strength. The sponsons are a very simple JAE like design with a flat ride pad (the width and angle I will not say).

This is the 6th iteration of this hull design. The tub and sponsons are legal in Q, S and T classes.

[urbs00007]

Here is a brief description of the T-hydro and some pics of the boat prior to the event.

The boat is my own design based loosely on the Raptor Rigger by Brian Buaas. The rudder assembly is from Chris Woods running a kitchen knife. The strut is from Lenny Blake at Rum Racing products with special bushings. 3/16" square drive system with flex cable, mostly Octura parts. I machined and broached my own motor couplers to adapt the 8mm shaft to square cable. Motor is a Lehner 22 series Hi-Amp. I will not say what exact wind or length used. Controller is a Schulze 40.160wk and I used a set of SLS V2 Magnum 10S 5Ah lipos. The prop is a stainless recasting from an existing two blade prop (I am not saying which one) that was cut down, profiled and thinned to a reasonable level but not too much so it had some strength. The sponsons are a very simple JAE like design with a flat ride pad (the width and angle I will not say).

This is the 6th iteration of this hull design. The tub and sponsons are legal in Q, S and T classes.

Tyler, why the need for square-drive cable?

[Darin Jordan]

Does anyone have the "OFFICIAL" Results from this event yet?? :)

[RaceMechaniX]

Darin,

Still waiting for Mark and Kim to return from Huntsville.

urbs00007,

I tried running wires but for several reasons they failed often. I went to standard flex cable for reliability. In a flexcable application there is tremendous axial force and torque applied to the cable particularly for a boat that accelerates from 0-140 in several hundred feet. Eliminating the thrust on the cable reduces stress and potential binding. It is also more consistent when the pushing on the strut compared to the motor with the cable wind-up.

TG

[urbs00007]

Darin,

Still waiting for Mark and Kim to return from Huntsville.

urbs00007,

I tried running wires but for several reasons they failed often. I went to standard flex cable for reliability. In a flexcable application there is tremendous axial force and torque applied to the cable particularly for a boat that accelerates from 0-140 in several hundred feet. Eliminating the thrust on the cable reduces stress and potential binding. It is also more consistent when the pushing on the strut compared to the motor with the cable wind-up.

TG

thats what i thought. what kind of bearing are you using at strut for thrust?

[RaceMechaniX]

Teflon thrust washer.

[urbs00007]

thanks tyler. one more question please. do you have any data that the batteries you ran were a deciding factor? if they were are they available to purchase?

[RaceMechaniX]

Hard to say how much of the difference was the batteries versus the controller. I am sure it was a little of both. Keep in mind I ran the smallest prop I had when I set the record. Earlier in the week I tried four other props with varying pitches and almost all resulted in the same 137mph speeds. I think the old controller and SLS batteries could have pushed one of the higher pitched props to higher speeds. We'll find out at the next event.

The SLS batteries are available from http://www.stefansliposhop.de/ I am not sure if he ships them internationally.

TG

[urbs00007]

are you data-logging this boat? and if no, why not?

[Darin Jordan]

We'll find out at the next event.

[properchopper]

Does anyone have the "OFFICIAL" Results from this event yet?? :)