Hobby King Apparition

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rdplain
    Junior Member
    • Jun 2011
    • 6

    #16
    took you long enough!



    Originally posted by lyndon915
    Man you beat me to posting a link to my own video!!
    The Miss Geico is going 42.0mph according to the gps and the fastest I have recorded with this setup is 43.2mph. We didnt get a top speed reading on the Apparition today as the GPS didnt work properly in the boat, will try and get one tomorrow.

    Comment

    • rdplain
      Junior Member
      • Jun 2011
      • 6

      #17
      Originally posted by penz
      Check all the screws on the rudder assembly, some of them were loose on mine, just check all screws. I have only ran mine twice, i keep getting water inside, i think its coming through the flex shaft so i got some grim racer speed grease see if that helps. Other than that ots a nice hull, its all about how you set it up. What esc are you running in yours?
      I did notice after the initial run, that the screw that holds the turning rod pivot was very close to falling off. Some blue Loctite and all is well!

      I greased the flex shaft before the first run and I got about 7 runs before i started getting water in the hull from the stuffing tube, completly dry on every run before that. The temps went WAY up because of the additional friction with water being in the tube. Upon disassembly, it was completly void of any grease, and filled with water.

      But i did hit 42.9 mph on 4S !

      Comment

      • penz
        Senior Member
        • Jun 2011
        • 139

        #18
        That pin your talking about, it has a small set screw that holds it in place, mine didn't even have the set screw!... and of the 4 screws that attach the rudder/strut assembly to the boat 3 of them were way loose... Geetting a small socket in there to tighten those was a pain in the rear!

        I'm having issues with all my grease coming out way to fast... its oozing out where the stuffing tube meets the strut... I wonder if I should seal this area?
        LST XXL-4074 Taco, Slash 4x4-3660 Taco, Appparition-3674 Taco

        Comment

        • rdplain
          Junior Member
          • Jun 2011
          • 6

          #19
          AND... The magic smoke has been let out...

          Luckily it was the cheap motor and not the ESC.
          Not sure what happened, about 3 minutes into the first run of the day, boat slowed way up, like the batteries were done, then it just stopped. Opening up the hatch literally "let the magic smoke out". A very rancid smoke at that. As I was disassembling the motor, there was no magnetic field left, and the winds looked like they were covered in melted chocolate. Pretty nasty stuff... Going to throw my UL-1 2030 kV motor in it and see what she does.

          Comment

          • lyndon915
            Member
            • May 2008
            • 38

            #20

            Comment

            • Just ADD Water
              Junior Member
              • Jul 2011
              • 14

              #21

              Comment

              • ron1950
                Fast Electric Addict!
                • Aug 2010
                • 3024

                #22
                let us know what temps etc the ul1 motor does speed also
                MY RETIREMENT PLAN?????.....POWERBALL
                74 vintage kirby clasic hydro, pursuit mono, mg, 47'' mono, popeye hydro...

                Comment

                • penz
                  Senior Member
                  • Jun 2011
                  • 139

                  #23
                  Originally posted by rdplain
                  AND... The magic smoke has been let out...

                  Luckily it was the cheap motor and not the ESC.
                  Not sure what happened, about 3 minutes into the first run of the day, boat slowed way up, like the batteries were done, then it just stopped. Opening up the hatch literally "let the magic smoke out". A very rancid smoke at that. As I was disassembling the motor, there was no magnetic field left, and the winds looked like they were covered in melted chocolate. Pretty nasty stuff... Going to
                  throw my UL-1 2030 kV motor in it and see what she does.
                  Hope that ul1 motor works out for you. The tacon 3674 1900kv I'm running in my app is solid! 4s with an x442 prop and temps only at 100...
                  LST XXL-4074 Taco, Slash 4x4-3660 Taco, Appparition-3674 Taco

                  Comment

                  • rdplain
                    Junior Member
                    • Jun 2011
                    • 6

                    #24
                    So the UL- 1 motor was a success.
                    4S - 47.5 Mph
                    5S - 54.8 Mph
                    Still with the Grim Racer 42x55 prop.
                    I was able to walk away from the Miss Geico at will. Boat was very stable, and still very controllable even at 50+ mph.
                    Very happy with this setup. The UL-1 ESC is NOT meant to anything over 4S, so i only did a few passes on 5S. Temps stayed in the 120's.
                    The stock bearings in the UL-1 motor were a little rough, so I replaced them with full ceramic bearings from Avid Bearing. I'm sure that was all the difference.

                    Comment

                    • SLOW
                      Member
                      • May 2009
                      • 37

                      #25
                      Got my apparition running today...
                      4s
                      Fiego 8xl
                      Octura m445
                      old etti 150 esc
                      53.6 mph...

                      Comment

                      • lyndon915
                        Member
                        • May 2008
                        • 38

                        #26
                        Video or it didnt happen

                        Comment

                        • rdplain
                          Junior Member
                          • Jun 2011
                          • 6

                          #27
                          Originally posted by lyndon915
                          Video or it didnt happen
                          The only thing the video would show, is his boat on it's lid...

                          TOO MUCH TORQUE~!~
                          Last edited by rdplain; 08-05-2011, 11:09 AM.

                          Comment

                          Working...