Is it a good choice or TOO much power? Will it fit with no mods?
Castle 1717 Direct FIT?
Collapse
X
-
-
the CC1717 does fit, a little snug with the water jacket
almost the same kv as the CC1520 1600kv.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8sComment
-
-
The 1580kv car version has 5mm shaft
The 1500kv air version has 6mm shaftComment
-
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8sComment
-
I removed the rear endbell and drilled cooling holes into the endbell, i replaced the stock CC endbell screws with leopard ones (i like them better, easier to install and remove) I then drilled holes in the front cap of the motor. I made a gasket around the endbell and installed a 12v brushless 40x40x20 computer fan that runs off of a 3s 2200 3c lipo. I attached the fan to the motor and the fan will draw heat away from the motor. I then modded the stock motor mount and allowed a gap between the motor and the motor mount to allow air to be allowed to be pulled threw the motor. I will be using a sr3300t rx with telemetry so I can get live motor temps on my dx3s radio. Haven't tried it yet but hell it's worth a try. If it doesn't work I slap a different motor into it and consider it a $70 learning lesson. So with that being said, a twin 1717 air cooled would be sick! JMO
Here's the thread on everything more in detail: http://www.rcgroups.com/forums/showt...1405388&page=7Comment
-
Final pic:Attached FilesComment
-
Here's something I have been working on. I wanted to use the car verison with a waterjacket on my vanquish hull but quickly found out jackets are very hard to find right now, so I decided to air cool a 1717 car verison.
I removed the rear endbell and drilled cooling holes into the endbell, i replaced the stock CC endbell screws with leopard ones (i like them better, easier to install and remove) I then drilled holes in the front cap of the motor. I made a gasket around the endbell and installed a 12v brushless 40x40x20 computer fan that runs off of a 3s 2200 3c lipo. I attached the fan to the motor and the fan will draw heat away from the motor. I then modded the stock motor mount and allowed a gap between the motor and the motor mount to allow air to be allowed to be pulled threw the motor. I will be using a sr3300t rx with telemetry so I can get live motor temps on my dx3s radio. Haven't tried it yet but hell it's worth a try. If it doesn't work I slap a different motor into it and consider it a $70 learning lesson. So with that being said, a twin 1717 air cooled would be sick! JMO
Here's the thread on everything more in detail: http://www.rcgroups.com/forums/showt...1405388&page=7
I'm thinking of trying water injection on a outboard setup
let the can fill with a constant flow of cool water.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8sComment
-
Comment
-
Comment
-
NEED PARALLEL CONNECTORS?? QUALITY 5.5MM, 8MM, 8 AND 10 AWG, GET THEM HERE:http://forums.offshoreelectrics.com/...est!&highlight=
Comment
Comment