Got my revolt

[MAMBA2200]

well i got my revolt yesterday overall i am very happy here is a few things i noticed
-all the gear on the back is way loose (no biggy)
-i got no owners manual or stickers
-when i turn the prop the motor wiggles back and forth
-there was nothing holding the hatch on so its scratched allot around the hatch hole (again no prob)
- i do have lock nuts on all hardware thats a plus
it almost seems like i got a boat that someone else had returned but i can fix all that is needed here is a video of the motor wobble

[Grimracer]

Hum.. No manual.. I bettter give you the contact info to Product Support.

Call em and see if they can get you setup.

Grim

Hobby Services
3002 N. Apollo Drive, Suite 1
Champaign, Illinois 61822
Attn: Service Department
Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F
E-mail: [email protected]


Also.. here

http://manuals.hobbico.com/aqu/aqub24-25-manual.pdf

[MAMBA2200]

thanks grim i have contacted omni thats where i got it from but so far have had no responce will give them a chance to make it right first

[bruceisla]

You appear to have either a bad coupler or a bent motor shaft. Try removing the coupler and spinning the motor shaft to see which is bad. It's possible the coupler is cross threaded. Video is a bit shaky and too short to look closely.

[MAMBA2200]

well they are sending me the missing item and i think the wobble is flex shaft which i have already got the upgraded shaft so all is good i can fix the rest

[MAMBA2200]

got my seaking 120a V2 and 150a eagle tree time to start the build as everything will be here today photobucket-41902-1348319541628_zps6eb26191.jpgphotobucket-35208-1348319555490_zpsa5d93341.jpg

[Mike Caruso]

got my seaking 120a V2 and 150a eagle tree time to start the build as everything will be here today [ATTACH=CONFIG]84896[/ATTACH][ATTACH=CONFIG]84897[/ATTACH]

Check out my gallery I mounted the ET to balance the boat out side to side. Aeromarine flex collet and Hughey shaft is what I am running trouble free. Stock prop runs good 45x68 pulls more amps but adds mph.
Have fun man.
Mike

[MAMBA2200]

well i got the rest of my parts and it was the flex shaft bent i dont see how they crammed it in there gonna call aquacraft today and see if they will send me another because this one is crap but i have the upgraded cable installed and all is wellphotobucket-15101-1348492385892_zps7b975a8e.jpg

[bruceisla]

Well .... you may be expecting a bit much. Flex cables flex .... that doesn't look like a kink (sharp bend).

[MAMBA2200]

this i know when i pulled the old one out it had like a 45 degree bend on the end of the cable

[stadiumyamaha]

I wouldn't bother getting them to replace the stock flex. They are so suspect that you don't want to risk losing a good prop. Many times they fail in the first couple of minutes. Jmo

[MAMBA2200]

i hear ya think i will take that advise

[MAMBA2200]

well its all done and ready for its first run here is some final picsphotobucket-35263-1348580145245.jpgphotobucket-26975-1348580127743.jpgphotobucket-18967-1348580114016.jpgphotobucket-35347-1348580158128.jpg

[ktodd]

Looks great! Looks thirsty for water Let us know how it runs

[MAMBA2200]

will do im off thursday thats when the maiden voyage will be and i will video it and post it up