ID some hardware anyone?

[BrickBait]

Have a look at these pictures below...
Can anyone name the manufacturer of these rudders and drives?
I think the first one is a MTC rudder, and the second a speedmaster rudder.

Looking to equip a MHZ Racemaster with either i Single Inline setup, or a dual rudder/single drive setup.
Going into some rather uncalm water with this
What would be a good distance from transom to leading edge of rudder in both setups?
And distance from transom to drivedogs?

Hope someone can share some experience with this boat size

20160524_150748.jpg

cache.jpeg

post-1851-1276369530,6785_thumb.jpg

temp_441.jpg

[Alfa Spirit]

This RC Boat Bitz is fine:

TITUS 61.JPG

This one is great too:

TITUS 52.jpg

[fweasel]

20160524_150748.jpg
MTC rudder, drive, trim-tabs

cache.jpeg
TFL rudder and drive

post-1851-1276369530,6785_thumb.jpg
MHZ rudder, unknown drive

temp_441.jpg
MHZ rudder, MHZ Trimax arneson drive

[BrickBait]

Thank you

But I guess they are hard to get then. Looks like MHZ has pulled them from the shop.
I do like the looks of the first one. MTC. Looks like 145mm from transom to leading edge. Isn't that a bit to long? Looks quite long.
I am trying to find info about what rudder length I need + distance to transom. And also how long a strut I need.

[fweasel]

MTC product is nearly impossible to get at the moment. MHZ stocks some of it, so check there first. Don't even bother trying to order it directly from MTC. Still waiting nearly 8months for my last order. I believe MHZ has discontinued the Trimax drive.

[koen]

i have a mhz phantom (it's the same hull)i run it with the setup as in the 2 picture with a tp 4070 1400kv without the trim tabs and turn fins and it run so good this hull is easy to setup

[BrickBait]

Sounds good koen.
What is the distance from transom to front edge of the rudder ? And from the bottom of the hull, to the bottom of the rudder ?

[koen]

form transom to edge rudder 12cm and form bottom hull to bottom rudder is 7cm

[Alfa Spirit]

If you want large size and high quality hardware have a look to WD200.

Further development of the proven rudder 38
for large monoboats, black anodized with line polished rudder
Length of the rudder boom to rudder axis 140mm or 202mm
Rudder blade length 135mm from lower edge cheek, total height 205mm

Order no.5043
Length with 140mm boom =165 mm
Price rudder with 140mm boom: 189,00 € incl.19% VAT plus shipping
Paypal price: 196,55 € including 19% VAT plus shipping order / order

Order no.5044
Length with 202mm boom =227mm
Price Rudder with 210mm boom: 211,00 € incl.19% VAT plus shipping
Paypal price: 223,60 € including 19% VAT plus shipping

http://www.wd200-modellbau.de/?HOME

[koen]

i have on the phantom a MTC stinger and a large TFL rudder, TFL hardware is good maybe not the very best but good for a nice price

[BrickBait]

form transom to edge rudder 12cm and form bottom hull to bottom rudder is 7cm

Thank you for that. Good info to get started with.


Alfa, those rudders are massive!
Should it be WD200 I would probably go with the smaller version.

712a53a7-c521-4b7f-b2e3-9bc3812dcf0c.jpg

[BrickBait]

7E2F71F2-E49E-46D4-A5CB-03D4930D0C7F.thumb.jpeg.26354d693323d22e0d3ecbc32d12f8bf.jpeg

Now see this.... That is what I am talking about

[fweasel]

[ATTACH=CONFIG]177394[/ATTACH]

Now see this.... That is what I am talking about

Those are Tenshock carbon rudders and a TFL drive

[BrickBait]

I don't dig the rudders, but the setup is sweet. I might go that way with some Werner or MTC hardware.