Etti 150 race Esc

[Flying Scotsman]

Let me first say that I feel your pain and understand your frustration. I've been there and pulled the hair out of my head.


Could it possibly be your setup? What setup did you use? What batteries did you use and rating?

Also, I have a Lizard Extreme and I am interested in your setup

Douggie

[EPower]

Let me first say that I feel your pain and understand your frustration. I've been there and pulled the hair out of my head.

Let me explain how the Etti repairs are handled. ALL repair and warranty correspondence is done from the Customer to the Dealer. You cant go directly to Etti. So I know should know every problem that's been had with my customers and their problems with Etti controls. This is important, because it allows me to know the number of problems happening out there. I can say that its not as bad as you are making it out to be. Its rather quite small and on par or a bit better than the other esc's out there. I've literally sent less than 20 esc's back for repair or replacement. That number pails in comparison to the number that are sold and currently running around. Also if the Etti esc's were as bad as you think I wouldn't be selling the product. For two reasons. 1st I just pain dont want to sell junk. 2nd for the simple fact that I have to pay the shipping costs for returning these esc's. Both back and forth.

Could it possibly be your setup? What setup did you use? What batteries did you use and rating?

`

Hi Steve
I understand that you have some interest in this thread because you sell Etti esc
so let's start here
I brought my Etti esc from you at the beginning of this year, ( ALL repair and warranty correspondence is done from the Customer to the Dealer) wrong when i contacted you by email you gave me mr Dee email address and told me to contact him directly (you may have a different policy for ovrseas coutomers?) so all shipping costs have come out of my pockets
since then i have been dealing with him
My setup
KB45 XL 1600 kv
2 X Zippy R 20c 4500 Mah 3s (running in series = 6s)
Octura M445 shrpened & balanced
with this setup i blew the caps on the esc sent it back to etti he repaired it and told me i should add the extra caps board he supplied & fitted it to the esc for me
got it back ran it with the zippys twice then brought some Hyperion 5500 Mah G3 35c 3s running in series making 6s same motor & prop

http://www.youtube.com/watch?v=od9n_93pYXU

this is the first run with the Hyperion batt,the next day i ran the boat again and after about two minutes it just stopped in the middle of the pond no visible dammage to the esc all caps where fine no bad smell but the esc was dead again
sent it back to Etti, I sent Dee an email with my setup and batt i was using, i waited for about 3 & 1/2 weeks he replied me (Please be informed that the problem 150A ESC has been repaired!
We have found your ESC has 12 x mosfets and 2 x IC were damaged)
i sent me the funds for the repair it arrived a week later and after two runs the same thing happened again just stopped
If his product could not handle my setup he should have told me so i would have sold his over rated esc and brought one that could handle the job very simple to me i could have saved me a few dollars
Adrian

[Flying Scotsman]

That motor is an amp hog

Douggie

[egneg]

I just got a 150 with extra caps so as of this time I don't have an opinion. But I have never smoked an ESC or motor. I have had a lipo puff once but I bought it used so the history of it is questionable. Folks need to be realistic with the capabilities of the equipment they are using - extreme setups that don't use full throttle most of the time will go up in ...

[EPower]

That motor is an amp hog

Douggie

Dee knows i started this thread so i guess he can join in

[Flying Scotsman]

Who is Dee? I can be stupid most of the time

Douggie

[EPower]

Who is Dee? I can be stupid most of the time

Douggie

LOL you should put your reading glasses on an read this thread proprely Dee is the man at Etti, anyways this is all i have to say,i have been put off boating altogether now, so i decided to sell all my boats and be done with it all the best to all you guys
Happy boating
Adrian

[Flying Scotsman]

LOL you should put your reading glasses on an read this thread proprely Dee is the man at Etti, anyways this is all i have to say,i have been put off boating altogether now, so i decided to sell all my boats and be done with it all the best to all you guys
Happy boating
Adrian

That is my problem...I am an old fart and just that the ALL BLACKS lost you might be in a bad mood and I might find my specs and I trust you continue FE boating

Douggie

[tth]

I have 2- Etti 150 esc's and they are wonderful. I will put them right up to, if not above the Hydra series from castle. I run slightly hotter setups than most "sport" boaters. These little controllers will take a lot. I hope you get your facts right about the KB motors and running them on 4500mah 20c discharge zippy's. You are running a very hot setup with lots of amps being demanded. Just trying to shed some light.

[Steven Vaccaro]

`
I brought my Etti esc from you at the beginning of this year, ( ALL repair and warranty correspondence is done from the Customer to the Dealer) wrong when i contacted you by email you gave me mr Dee email address and told me to contact him directly

I stand corrected, you were the first and last customer of mine to go directly to Dee. I forgot about this. After I asked you to contact Dee, he emailed and asked us to have all customers come to us for repairs and warranties.

[cybercrxt]

Steve, I just sent you a message tonight asking how to send my Etti 150 race back for repair. I ran it twice on a boat setup that worked fine with a hobbywing 180a before trying this etti on it. Please email me back when you get a chance. Thanks, Michael Luszcz, [email protected]

[Steven Vaccaro]

I replied to your email yesterday.

Just a fyi about forums, its a bad idea to post your email. It will get picked up by spam bots.