carbon fiber inlay

[johnf]

Looks good

[Fella1340]

Awesome job! I hope we get some video of the boat on the water. It looks so cool
inside now, it must be faster! Have you got another project lined up we can tune into
next?

[kfxguy]

Awesome job! I hope we get some video of the boat on the water. It looks so cool
inside now, it must be faster! Have you got another project lined up we can tune into
next?

Lmao. I just wrecked it! I was being a dumbass and was trying to splash my kids on the bank. Well. I ran it aground at full speed. I managed to go right through my recovery boat and destroyed it completely. Time to build another. Lol. The geico suffered minor damage. It did crack the hull in a few places. Good thing I can fiberglass. Hahaha. Im laughing to keep from crying right now. Here's some damage pics. Bent the offset rudder bracket. Everything I did stayed put tho. I wanted it a different color anyway.

I have 4 projects coming up in the next few days if you want me to start a thread on them.
Im building a 37" carbon fiber daytona for my buddy
Building a much better recovery boat
Im getting a carbon fiber cheetah to finish for myself
And im building myself a 26" bling rocket on steroids.


20131103_162801.jpg

20131103_162638.jpg

20131103_162609.jpg

20131103_160929.jpg

[lenny]

Ok where is the video of all that fun you just had.

[kfxguy]

Ok where the video of all that fun you just had.

Im uploading my horrible driving to youtube right now. Stay tuned. Unfortunately I didn't get my stupid wreck on video. Kinda wish I had so I could go back a remind myself how dumb I was. Lol

[lenny]

We need a thread just for the blooper video's,
To make us all feel better at times like this.

[Fella1340]

Wholly s--t, you couldn't do that again if you tried!! Is there anything you didn't hit!? It seems you do a thorough job on everything you do! Seriously, that's a bad piece of luck. Now you can finish it exactly the way you want it. You might as well start where you left off on your last post with the rebuilding of MG. I for one would like to see you post the other boats your doing here. Sounds like you will be a busy guy. No time like the present to get started! Cool retrieval boat by the way. I wonder what the damage would have been like without the added carbon fiber you added? I hope the damage is more superficial than anything else. Congrats again on a very thorough job! Glad you could see the humour in it. Jeff

[kfxguy]

Wholly s--t, you couldn't do that again if you tried!! Is there anything you didn't hit!? It seems you do a thorough job on everything you do! Seriously, that's a bad piece of luck. Now you can finish it exactly the way you want it. You might as well start where you left off on your last post with the rebuilding of MG. I for one would like to see you post the other boats your doing here. Sounds like you will be a busy guy. No time like the present to get started! Cool retrieval boat by the way. I wonder what the damage would have been like without the added carbon fiber you added? I hope the damage is more superficial than anything else. Congrats again on a very thorough job! Glad you could see the humour in it. Jeff

Thanks man. Look on YouTube under my user to see my vids. I have the retrieval boat on there. That thing is frigging awesome at how good it works. It had carbon fiber reinforcing in it too. No damage to any of the components or cf work. Just the cheap tupperware I used. Lol. Here's a sneak peak at the new recovery boat. Its gonna be fiberglassed.

20131103_192054.jpg

Here's one of my vids. My driving usually doesn't suck this bad.....the sun is in my eyes.

https://www.youtube.com/watch?v=XgGST6OJedc&feature=youtube_gdata_player

Like I said, click on my user name and you can see the recovery boat vids.

On a side note, ill fix the geico in the next few days and paint it a better green color like I wanted too anyway. Just gave me a reason now. Ill flatten and sharper the sponsons. Can't decide if I wanna remove the trim tabs. Them puppies really work. I can change the whole attitude of the boat with them. It does run a little wet scrubbing some speed. Im taking this power attempt out of this boat anyway and putting it into the cheetah. Then im putting a leopard 4082 2200 in the geico. I have a higher amp esc coming to.

[rickwess]

It was running nice in the video. Half the fun is building them anyway.

[Fella1340]

You've got the geico moving good, now you want to put a 4082 in it? I would keep the trim tabs:) that's going to be a rocket! The rescue boat is awesome. Its the first one I have seen that goes underneath the hull and can grab it from any angle. I'm sure your going to miss it, time for the next level of rescue boat! That shocker was really moving to, what did you have in that? I have a 26" here that needs that kinda livening up! Its to bad you didn't get that little mishap on video, that sure would have been something to see. One minute everything is good, next carnage everywhere!

[kfxguy]

It was running nice in the video. Half the fun is building them anyway.

Thanks. I honestly have more fun building it than running it.....weird I know.

[kfxguy]

You've got the geico moving good, now you want to put a 4082 in it? I would keep the trim tabs:) that's going to be a rocket! The rescue boat is awesome. Its the first one I have seen that goes underneath the hull and can grab it from any angle. I'm sure your going to miss it, time for the next level of rescue boat! That shocker was really moving to, what did you have in that? I have a 26" here that needs that kinda livening up! Its to bad you didn't get that little mishap on video, that sure would have been something to see. One minute everything is good, next carnage everywhere!

I thought the 4082 would be a downgrade from the motor I have? I have a 1515 2200kv castle in it. The 4082 will be here's tomorrow so ill compare.

The shockwave has a 1512 2650kv castle motor in it. That thing will scoot but its not stable. If you have a brushless one, put a higher amp (at least 60 amp) esc in it. Keep the stock motor. Run 4s in it with a 45mm graupner prop. That's the setup my son have and it does 35ish mph. With a 5400 mah battery it runs for about 20 mins lol. Does not run hot at all. What I have in mine is way too much. That's why im swapping everything over to the bling hull. Im hoping it'll be more stable.

My rescue boat.....im gonna miss it. It was so frigging awesome. It never failed me. It would even bring back my canopy and canopy seal. I hope my next one could live up to it. That thing would turn so sharp and was extremely stable and controllable.

[rickwess]

I thought the 4082 would be a downgrade from the motor I have? I have a 1515 2200kv castle in it. The 4082 will be here's tomorrow so ill compare.

The 4082 is similar to the 1524 is you believe the printed specs.

[Fella1340]

I didn't realize you had a 1515 2200kv in there. Your still changing it out for a 2200kv motor, are you hoping for less torque and performance because its a Leo motor? I'm not familiar enough with the difference in poles/wind to even guess. The 26" boat I have is a R2 hobbies hull and my first build. It just recently became my learn the basics of cf boat. Turned out good. I haven't selected a new motor.for it yet, 2650kv seems like it would be a little much! I said first build, so far its one of one. The hull in my avatar is going to be number two. I have all the parts here for it (plus a hobby stores worth again) and its driving me crazy not being able to get to work on it. Recovering from back surgery at the moment and having a 5 year old is enough work at the moment! He loves the boats, good driver to! He's getting a hk genesis for Christmas, it will be seriously detuned from its already not so.fast stock self. It will be taller than him! He's loved the genesis since he first saw one and lucky for me the price is reasonable. We don't run where there's anyone else around. The only thing he can hurt is the boat (disclaimer for people who think that's to much boat for a five year old). Good luck on the rescue boat build, hopefully your new one will be able to slide underneath it the way the other one did. So many of the rescue boats I have seem rely on you lining the boat up and getting it between the arms. The way you could grab the boat from the side like that made it awesome. I hope you post the second generation of it, I have more than enough lying around to build one. What type of motor did you use?

[kfxguy]

I didn't realize you had a 1515 2200kv in there. Your still changing it out for a 2200kv motor, are you hoping for less torque and performance because its a Leo motor? I'm not familiar enough with the difference in poles/wind to even guess. The 26" boat I have is a R2 hobbies hull and my first build. It just recently became my learn the basics of cf boat. Turned out good. I haven't selected a new motor.for it yet, 2650kv seems like it would be a little much! I said first build, so far its one of one. The hull in my avatar is going to be number two. I have all the parts here for it (plus a hobby stores worth again) and its driving me crazy not being able to get to work on it. Recovering from back surgery at the moment and having a 5 year old is enough work at the moment! He loves the boats, good driver to! He's getting a hk genesis for Christmas, it will be seriously detuned from its already not so.fast stock self. It will be taller than him! He's loved the genesis since he first saw one and lucky for me the price is reasonable. We don't run where there's anyone else around. The only thing he can hurt is the boat (disclaimer for people who think that's to much boat for a five year old). Good luck on the rescue boat build, hopefully your new one will be able to slide underneath it the way the other one did. So many of the rescue boats I have seem rely on you lining the boat up and getting it between the arms. The way you could grab the boat from the side like that made it awesome. I hope you post the second generation of it, I have more than enough lying around to build one. What type of motor did you use?

I used my stock geico 1500kv motor on 2s with a big graupner prop. so I guess maybe the leopard motor is a bigger motor powerful series than my castle. Maybe castle will stay put and leopard in cheetah. Ill keep you posted on everything.