Tiquemans HPR 135

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nata2run
    customcfparts.com
    • Nov 2011
    • 1837

    #211
    Originally posted by flraptor07
    Got my parts today Kent, looks great!!
    Cool!! When do we get to see the boat?
    Visit www.customcfparts.com | Custom Boat Building | Custom Carbon Fiber Parts | Custom Graphics | LMT Premium Dealer | MGM Premium Dealer | YouTube | Facebook
    "Follow someone's footsteps and you will always be a step behind"

    Comment

    • nata2run
      customcfparts.com
      • Nov 2011
      • 1837

      #212
      Originally posted by tiqueman
      Dont hit a fence??? How the hell are you running your boats?????

      Once the trays are here and i can get them installed and get all the tubes cut to height for the esc plate... install electronics, plumb it and add floatation i think she'll be about done. Oh i need to get the other hatch painted too. Thatll be my running hatch.


      And john, YES I AM.
      I didn't hit a fence lol, but I always fear I will. Sadly my newest build did, lucky nothing major happened.
      Visit www.customcfparts.com | Custom Boat Building | Custom Carbon Fiber Parts | Custom Graphics | LMT Premium Dealer | MGM Premium Dealer | YouTube | Facebook
      "Follow someone's footsteps and you will always be a step behind"

      Comment

      • Maciek74
        Member
        • Jun 2012
        • 48

        #213
        Hi, i just finished reading ur whole thread after i decided to build my first double motor cat. I tried to build MHZ 1380 but it was so poor finished that i sent it back, and now ordered HPR135 bulletproof, so ur build will be inspiration for me :) (beside the painters job ofc )
        Which props will you be using, ive read Octura X457 (3 blades?) but is it final size or just first step? Which shaft are you using 3/16 or 1/4? I have 1/4 shafts are they available in this size so far i fiund only 60mm+?
        Ill start my own thread after i get hull so will be pleased if you visit it from time to time with some advices :)

        Regards
        Maciek

        Comment

        • nata2run
          customcfparts.com
          • Nov 2011
          • 1837

          #214
          Maciek, congrats on your hpr135! They are awesome, both looking and driving. Not sure what you got but they mainly run 1/4 shaft turned to 3/16 to fit most props. Depending on you motor/esc setup, you can start with 447 props and work from there. You can get 80mph with 447 props and not put a great amount of load on your system. Later you can then run larger and cut down props. What power system do you plan running? Those boats can quickly become too fast lol
          Visit www.customcfparts.com | Custom Boat Building | Custom Carbon Fiber Parts | Custom Graphics | LMT Premium Dealer | MGM Premium Dealer | YouTube | Facebook
          "Follow someone's footsteps and you will always be a step behind"

          Comment

          • Maciek74
            Member
            • Jun 2012
            • 48

            #215
            Nata, 2xLMT3060/14 500kv on 15s, i know rpm bit too low but i bought them ocasionaly, probably will change in future :) but lets dont trash Tiq thread, ill make my own soon :)

            Comment

            • nata2run
              customcfparts.com
              • Nov 2011
              • 1837

              #216
              Is this build done yet? I always wonder...
              Visit www.customcfparts.com | Custom Boat Building | Custom Carbon Fiber Parts | Custom Graphics | LMT Premium Dealer | MGM Premium Dealer | YouTube | Facebook
              "Follow someone's footsteps and you will always be a step behind"

              Comment

              • tiqueman
                Fast Electric Addict!
                • Jul 2009
                • 5669

                #217
                Originally posted by nata2run
                Is this build done yet? I always wonder...

                Unfortunately no it is not Kent. Its been boxed up since the end of April and no telling when it will come back out. Life has gotten in the way as well as our move and I have no where good set up yet to build. Perhaps by years end but who knows????
                -Scott
                Geico epoxy laminate hatch sale thread Black Jack epoxy laminate hatch sale thread
                HPR06 6S Twin HOTR Genesis (SOLD) Vantex 32" cat Geico racing
                WEST FL MODEL BOAT CLUB www.scottskiracing.com

                Comment

                • nata2run
                  customcfparts.com
                  • Nov 2011
                  • 1837

                  #218
                  Sad to hear buddy, hopefully you get a chance to finish her off. Did a move myself, and man it's pain to get back into it all and find room. Be cool!
                  Visit www.customcfparts.com | Custom Boat Building | Custom Carbon Fiber Parts | Custom Graphics | LMT Premium Dealer | MGM Premium Dealer | YouTube | Facebook
                  "Follow someone's footsteps and you will always be a step behind"

                  Comment

                  • tiqueman
                    Fast Electric Addict!
                    • Jul 2009
                    • 5669

                    #219
                    Originally posted by Maciek74
                    Nata, 2xLMT3060/14 500kv on 15s, i know rpm bit too low but i bought them ocasionaly, probably will change in future :) but lets dont trash Tiq thread, ill make my own soon :)

                    I apologize for losing track of this and your questions and comments. Im running 457 2 blade that I have detongued and I am running 1/4" flexes into HPR drives. ill keep an eye out for your thread.
                    -Scott
                    Geico epoxy laminate hatch sale thread Black Jack epoxy laminate hatch sale thread
                    HPR06 6S Twin HOTR Genesis (SOLD) Vantex 32" cat Geico racing
                    WEST FL MODEL BOAT CLUB www.scottskiracing.com

                    Comment

                    Working...