WTB: 32+ hull

[minikitty]

Looking for a 32+ deep v or cat hull. I want to make it a gasser

[befu]

what gas

By gasser are you saying zenoah type gasser, or a smaller nitro motor?

Might have something for you. More racing design or scale design?

Brian

[minikitty]

Yeah a zenoah type. i'm looking for a racing desgin.

[Brushless55]

32" is small for a gasser

[Dangerous_Toys]

Yes, 32" is small for a gasser. My Rio is I believe 51"

[Dangerous_Toys]

32" would be good for Nitro, lets say a CMB .67 to .90

[minikitty]

I'd like to do a nitro. But I have an extra gasser engine i wanna use

[befu]

mono

I have a 40" mono with a zenoah in it now, surface drive hardware. I could take the motor and exhaust out of it or strip it down further. I will have to take some pictures and post them for you. It is a mid v. Not sure, maybe 20 degrees? White gelcoat, kevlar layup, strong boat.

also have a true deep vee, 24 degree deadrise, 52" long, kevlar layup. A couple actually, one has an old homelite in it. Another one was that kevlar/carbon blend, vacuum bagged in epoxy, carbon honeycomb for the the engine stringers. 52" long, foam flotation up front, stringers and built in radio box, about 5 lbs. That was going to be my fast boat, but got out of the nitro and gas. Want any .90 piccos?

will get pics tomorrow.

Brian

[Brushless55]

I have a 40" mono with a zenoah in it now, surface drive hardware. I could take the motor and exhaust out of it or strip it down further. I will have to take some pictures and post them for you. It is a mid v. Not sure, maybe 20 degrees?

also have a true deep vee, 24 degree deadrise, 52" long, kevlar layup. A couple actually, one has an old homelite in it.

will get pics tomorrow.

Brian

Kevlar, sweet!

[Alexgar]

i got a 32 nitro demoed and bare has a strut i was building for bl but am not that far along. no gas will fit but its stripped of mounts you chose the powerplant

[Alexgar]

hydro

[tomstoys2]

I have a 43" Dumas Skater that has a 23cc Zenoah currently installed. I planned on pulling the motor anyway. It's about 85% complete if you interested.
Tom

[tiqueman]

Dumas 45" V hull

http://forums.offshoreelectrics.com/...ad.php?t=13083

[befu]

40" mono

Pretty straight forward. shallower V, set up for surface drive, 1/4" flex, 23cc zenoah modified by midwest zenoah, wrap to center tuned pipe, 1/4 scale rudder servo, remote charge jack on the radio box for the rc battery.

The rails on this one is 1/8" balsa core with carbon fiber on both sides. I forget what the specs were, but it is like the weight of 1/8" light ply and the strength of 1/4" aircraft ply or something. Very nice stuff, very strong, rather pricey. Hmmm, I might have an outrunner that would push this thing as a sport setup!

Couple of chips in the front that need to be patched, polyester gelcoat and kevlar layup. Setup more for heat racing.

Brian

[befu]

52" deep vee

I have a few of these. From polyester gelcoat and kevlar that will hold a homelite, the carbon/kevlar one pictured here (no gelcoat - looks rough), to a couple not put together yet.

This one was setup for a .90 picco as the rails are 4" apart. Not sure you can fit a newer zenoah in it. it would be fast if you could. carbon fiber/nomex honeycomb core engine rails, all epoxy, vacuum bagged, strong! make you a deal with two picco .90s with fuel tanks and a Irwin quiet pipe.

Brian