FighterCat and Flier ESC's 3-20S 10A, 3-16S 300A and 3-8S 400A ESC's

[RaceMechaniX]

Hello All,

I have been hanging onto these long enough and don't plan on running so they are up for sale.

First ESC is Fightercat branded Flier ESC rated at 3-20S and 80A maximum. This was a special extra HV version. It's been bench tested, but never run in a boat. Asking $150 Shipped.

Second ESC is a Fightercat branded Flier ESC rated at 3-16S and 300A maximum. This was the standard HV version. It's been bench tested, but never run in a boat. Asking $250 shipped. ***Sold to meangeneracing***

Third ESC is a Flier double board 3-8S 400A ESC. This was a prototype them made for me. It comes with the USB programmer and the handheld programmer. It's set-up for a rotary pot switch instead of the normal receiver connection as I was using it for bench testing motors. The USB programmer and online software will allow it to be converted back to a normal receiver input. I will have to email the buyer a copy of the software. Asking $250 shipped. ***Sold to Blake T***

I can change any of the settings in any of the controllers prior to shipping if you do not have the programming box. These are getting hard to find.

I am open to trades for Lehner motors or other ESC's like YGE, Schulzes, Kontroniks of equal value.

-TylerFC 3-20S 80A ESC Pic 1.jpgFC 3-16S 300A ESC Pic 2.jpgFC 3-16S 300A ESC Pic 1.jpgFC 3-20S 80A ESC Pic 2.jpgFlier 3-8S 400A ESC Pic 1.jpg

[RaceMechaniX]

Additional picture of the double board 400A controller.Flier 3-8S 400A ESC Pic 2.jpg

[meangenesracing]

Tyler, I will take the 300A if it would work for my setup we talked about in the Backlash with a TP 5680

[RaceMechaniX]

Hi Eugene,

Yes this ESC will work well with the 5680. I tested an 8S 300A FC controller with a 5670 in my Q hydro. Ran good with no issues.
I can program in the timing numbers for you before I ship. Did you decide on the wind yet?

-Tyler

[meangenesracing]

Sorry Tyler I should have specified 10s I decided on. Either the 5y. 650 kv or the 4y 800 kv. Steven has both in stock. Which one you think? thanks

[BlakeT]

Hi Tyler, I’m interested in the 3-8s 400 amp esc. Any chance you would be able to program it back to normal before shipping it?

[RaceMechaniX]

Hi Blake,
Yes I can program it back and check it before shipping to you.
-Tyler

[BlakeT]

Thanks Tyler, I will take it. I’m just not too savvy with technology, It still comes with program box?

[RaceMechaniX]

Sorry Tyler I should have specified 10s I decided on. Either the 5y. 650 kv or the 4y 800 kv. Steven has both in stock. Which one you think? thanks

Eugene it will depend on what size props you want to run. 650 would likely be the best as you can run gas size props will hook up better in rough water. With 800kv you will be more limited in prop selection and in a purgatory range between 3/16" and 1/4" bores. Go with 650kv.

[RaceMechaniX]

Thanks Tyler, I will take it. I’m just not too savvy with technology, It still comes with program box?

Blake, yes the 400A double will come with the USB programmer and the program box.

[meangenesracing]

Eugene it will depend on what size props you want to run. 650 would likely be the best as you can run gas size props will hook up better in rough water. With 800kv you will be more limited in prop selection and in a purgatory range between 3/16" and 1/4" bores. Go with 650kv.

OK sounds good the 650 kv it is with the 300 amp esc. I think I still have your paypal addy. I'll get it sent shortly, thanks again

[meangenesracing]

Paypal sent

[BlakeT]

Sounds good, when you have time can you send over your paypal address in a PM, thanks!

[RaceMechaniX]

Hello Eugene, Money received. I will get this in the mail tomorrow.
Blake, PM imbound for the PP address.

Thx,
Tyler

[meangenesracing]

Hello Eugene, Money received. I will get this in the mail tomorrow.
Blake, PM imbound for the PP address.

Thx,
Tyler

Ok thanks Tyler, please program for my setup as I don't have a program box. No hurry on shipping