Tweet
SOLD
I purchased this from Travis a couple months ago, the build of this boat is 1st class. He built this to run in the 90s+ and I’m content with running 60s in circles, I really don’t need a boat with this capability. I enjoy building myself and am putting a list together for a tunnel build.
He only ran it a few times to start dialing it in, with just a couple laps each time. I never set it up after receiving it so it’s basically brand new. Click the link for the build thread, everything is mostly the same as when built I believe. The grooved servo mount was replaced with an identical one with no groove.
https://forums.offshoreelectrics.com...Doo-mono-build
Parts list:
34” KBB fiberglass hull
Carbon fiber inlay
Hatch is heavily reinforced
Carbon kintec adjustable motor mount
.187 flex
Speedmaster billet hardware
Sealed ball bearing strut
Carbon battery trays
Carbon esc mount
Custom carbon servo and receiver mount
Custom carbon wet well
Strut is adjustable for height and angle
Hatch seal that does not leak
Carbon vinyl window decal
Castle bec
Billet steering rod ends, high end no slack
Super thick steering rod
Led voltage display flush mounted in servo mount
*stand not included
Before I purchased, I priced out how much it would cost to buy everything as it sits and came up with roughly seven hundred worth of parts and building supplies. You will be paying one hundred and fifty for the labor of a top notch boat builder that was built for himself.
$850 Shipped to lower 48 by usps priority, add extra for insurance if you wish.
D6CA065B-AAE6-4D73-BD33-CFBE6E40222F.jpg3F0F6BD8-F433-4EF0-97E9-C5BE447ACF54.jpg2C30169D-0425-42C8-9E9D-5618B3CAAC59.jpg8B3DE161-DC31-4B9C-901C-0D990A648C6B.jpg01E3D87D-A2FA-4C62-8C7D-4BE2590C3783.jpg
I purchased this from Travis a couple months ago, the build of this boat is 1st class. He built this to run in the 90s+ and I’m content with running 60s in circles, I really don’t need a boat with this capability. I enjoy building myself and am putting a list together for a tunnel build.
He only ran it a few times to start dialing it in, with just a couple laps each time. I never set it up after receiving it so it’s basically brand new. Click the link for the build thread, everything is mostly the same as when built I believe. The grooved servo mount was replaced with an identical one with no groove.
https://forums.offshoreelectrics.com...Doo-mono-build
Parts list:
34” KBB fiberglass hull
Carbon fiber inlay
Hatch is heavily reinforced
Carbon kintec adjustable motor mount
.187 flex
Speedmaster billet hardware
Sealed ball bearing strut
Carbon battery trays
Carbon esc mount
Custom carbon servo and receiver mount
Custom carbon wet well
Strut is adjustable for height and angle
Hatch seal that does not leak
Carbon vinyl window decal
Castle bec
Billet steering rod ends, high end no slack
Super thick steering rod
Led voltage display flush mounted in servo mount
*stand not included
Before I purchased, I priced out how much it would cost to buy everything as it sits and came up with roughly seven hundred worth of parts and building supplies. You will be paying one hundred and fifty for the labor of a top notch boat builder that was built for himself.
$850 Shipped to lower 48 by usps priority, add extra for insurance if you wish.
D6CA065B-AAE6-4D73-BD33-CFBE6E40222F.jpg3F0F6BD8-F433-4EF0-97E9-C5BE447ACF54.jpg2C30169D-0425-42C8-9E9D-5618B3CAAC59.jpg8B3DE161-DC31-4B9C-901C-0D990A648C6B.jpg01E3D87D-A2FA-4C62-8C7D-4BE2590C3783.jpg
Comment