Proboat Impulse 31 V2, Upgraded, Extra 1500-Kv Motor

[skeeler]

I don't have time for RC anymore, so I'm selling this upgraded Proboat Impulse 31 V2. Here's a summary of the boat's modifications and condition:

• Additional two-part kintec foam in the front.
• Reinforced the motor mount.
• Hatch locks on the canopy.
• Reinforced the underside of the canopy rails with carbon fiber.
• Partial carbon fiber inlay to the canopy, front and rear.
• Upgraded the size of the wire on the 80a esc to 10 gauge.
• Large bullets right at the esc to connect the larger wire to the smaller factory wire.
• Castle 6.5-mm polarized connector on ESC. I can include some EC5 connectors if you like.
• Stock motor with aftermarket high-quality ceramic sealed bearings.
• Dynamite 1500-Kv, 6-pole motor also included.
• Upgraded billet adjustable (with a hex key) trim tabs.
• Brass tunnels through transom for easy trim-tab adjustment.
• Stock trim tabs also included.
• Aftermarket turn fins.
• Stock turn fins also included.
• Billet antenna mount.
• Extra rudder and stinger included.
• Carbon GPS mount
• Stock Spektrum transmitter and receiver included.
• Some minor spider webs in the paint, which is normal for these boats. There's no structural damage. Where the original canopy stud inserted into the hull, it cracked on top and upset the sticker. That hole has been filled and better hatch retention system installed. There is also some spider webbing on the top of the canopy.

I'd like $120 for the boat and $30 for shipping in the contiguous 48 states. Let me know if you have any questions.

See the photos in this post and the next.

For_Sale - 7.jpg
For_Sale - 20.jpg
For_Sale - 18.jpg
For_Sale - 17.jpg
For_Sale - 19.jpg

[skeeler]

More photos:

For_Sale - 15.jpg
For_Sale - 21.jpg
For_Sale - 24.jpg
For_Sale - 10.jpg
For_Sale - 13.jpg

[skeeler]

Stock hardware:

For_Sale - 22.jpg

[rw442]

Wanted to ask how did you reinforce motor mount? i had one of these boats and regret selling but I did have a problem with motor mount nut inserts pulling out. interested in buying yours but don't want to have the same problem. Thank you for your reply.

[Bp9145]

I'll take it

[limitedr1]

man I'm always just alittle to late for these deals!! let me know if falls through

[bikergreen]

I'll certainly take it if previous falls through. THanks

[Bp9145]

I apologize for not posting sooner. . .funds have been sent
thanks,
Brian

[Bp9145]

Hi Michael,
I received the boat and sent you a pm concerning FedEx carelessness with handling the package even when FRAGILE was written all over the box. The box was all beat up with the seams ripped opened lengthwise. . . pm'd you with details but I'm quite happy with the boat and your speedy delivery.. . .thank you

[boatsrnew2me]

Hi Michael,
I received the boat and sent you a pm concerning FedEx carelessness with handling the package even when FRAGILE was written all over the box. The box was all beat up with the seams ripped opened lengthwise. . . pm'd you with details but I'm quite happy with the boat and your speedy delivery.. . .thank you

ya know sometimes i swear you write fragile on a box and they just wanna kick it around on purpose . i try not to do that for that very reason .

[skeeler]

I responded by PM. Let me know how FedEx treats you when you talk to them.

[Bp9145]

I just want everyone to know that Michael is not in any way at fault here. He packed it well with layers of bubblewrap but unfortunately, FedEx didn't take great care in handling it since the box no longer sits flat like a box should sit on the floor. It's tilted and the seams are ripped open with bubblewrap sticking out. . .it's leaning to its sides. Michael expressed great concern but I'm going to handle the situation myself with FedEx and if it doesn't go well, I'm able to fix the slight damage. . .I'm still submitting a great rating for Michael.