F/S JetChopper 30 Mono Setup

[Tamelesstgr]

Hard decision, but I want to try a gas boat, specs:

Jet Chopper hull, new as of December 2016, 30" long
I added a Carbon Fiber inlay to the hull and a carbon fiber transom plate
Motor: SSS 3674 - 2075kv with Carbon Fiber mount
ESC: Seaking T180 V2 (very desireable)
Servo: ProBoat standard (has been waterproofed)
Tx/Rx: ProBoat (Rx waterproof with Traxxas waterproof case)
Carbon Fiber battery trays
Aeromarine motor coupler (5mm to .187 - 3/16" cable)
OSE .187 - 3/16" flex cable
Speedmaster Stinger
TFL Rudder
TFL Turn fins
TFL Trim Tabs
TFL Servo Mount
Kintec water lines (dual pickups)
M3 stainless hardware throughout
M3 stainless hatch hold down

Boat is stable and runs good with 40-45mm props. Cooling works well, I have datalogs if you are interested in seeing any information on the setup.

Asking $500 plus shipping (estimate $50 lower 48)
Add EagleTree V4 datalogger with all sensors for $100
Add (2) 2s Zippy Compact 5000mah packs for $40

Running Video in the past few weeks:

https://www.youtube.com/watch?v=cyLERJ2YlsU

20170510_211757.jpg

20170507_172409.jpg

20170420_211438.jpg

20170420_211914.jpg

20170419_211326.jpg

[Tamelesstgr]

Here is a link to the build log:
https://forums.offshoreelectrics.com...hopper-30-Hull

20170327_221006.jpg

20170327_221011.jpg

20170317_224605.jpg

[Tamelesstgr]

Bump

[bikergreen]

Thanks for the comments in my WTB thread - That option is a little closer to what I am looking for. How did you find this boat handled a bit of chop? Doesn't look like its a race only hull profile like you'd see on a pursuit etc. Any idea if you could fit a 40mm motor in that mount? also what would you want for the motor included? Shipping would be to 98281

[Tamelesstgr]

It's not a deep-v, but if say it handles chop pretty well. The motor mount can fit a 40mm can, but you woukd need to switch out the tail ring for a 40mm. It's a 36mm in there now, about a $7 change. I'd include the SSS motor in there now for $300 plus shipping, I'll try to get you a quote tomorrow.

[bikergreen]

Thanks - whats the beam width on the hull?

[Tamelesstgr]

Boat measures:

30" in length (without hardware)
9" wide
5" high

Fed-Ex ground to the West coast is showing about $59. How's $330 shipped with the motor sound and I'll cover the rest?

[bikergreen]

I found some more details on the hull and some pics of the profile from the back and I don't think it's going to be the boat for me. Really like your build but I need to find my self a proper Deep-V for the running I want to do. Thanks for the back and forth man GLWS

Boat measures:

30" in length (without hardware)
9" wide
5" high

Fed-Ex ground to the West coast is showing about $59. How's $330 shipped with the motor sound and I'll cover the rest?

[wolffman]

hi! How much would be the hull whit hardware?
Do you ship to amsterdam?

do you have an email?

[Tamelesstgr]

my email is [email protected]
I'll have to look into international shipping, I'll try to get a quote this week, travelling for work.

[MG1234]

Is this a different boat than the one that just sold ?