F.S. LIKE-NEW `HITEC SERVOS' BBs & MGs!

[K.R.Joye]

Selling large qty of items for a good friend. Like-New Hitec Servos seen little to no use. Everything but original box included.

(3) `HITEC HS225-MG ' Servos, each comes w/hardware kit!
Retail $26.00
Asking $16.50 Shipped CONUS ****2 SOLD, only 1 available****
Specs:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.14sec/60° at no load
Operating Speed (6.0V): 0.11sec/60° at no load
Stall Torque (4.8V): 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V): 66.65 oz/in. (4.8kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 300mA no load operating
Current Drain (6.0V): 8.8mA/idle and 340mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: 1 Ball Bearing and 1 Oilite Bushing
Gear Type: 4 metal and 1 nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematic
Weight: 1.10oz (31g)

(1) `HITEC HS425-BB ' Servo, comes w/hardware kit!
Retail $13.00
Asking $6.50 Shipped CONUS
SPECS:
Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.21sec/60° at no load
Operating Speed (6.0V): 0.16sec/60° at no load
Stall Torque (4.8V): 45.82 oz/in. (3.3kg.cm)
Stall Torque (6.0V): 56.93 oz/in. (4.1kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: Yes
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 150mA no load operating
Current Drain (6.0V): 8.8mA/idle and 180mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: Dual Ball Bearing
Gear Type: Nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: See Schematics
Weight: 1.6oz (45.5g)

(1) `HITEC HS225-BB ' Servo, comes w/hardware kit!
Retail $18.00
Asking $13.50 Shipped CONUS
SPECS:Control System: +Pulse Width Control 1500usec Neutral
Required Pulse: 3-5 Volt Peak to Peak Square Wave
Operating Voltage: 4.8-6.0 Volts
Operating Temperature Range: -20 to +60 Degree C
Operating Speed (4.8V): 0.14sec/60° at no load
Operating Speed (6.0V): 0.11sec/60° at no load
Stall Torque (4.8V): 54.15 oz/in. (3.9kg.cm)
Stall Torque (6.0V): 66.65 oz/in. (4.8kg.cm)
Operating Angle: 45 Deg. one side pulse traveling 400usec
Continuous Rotation Modifiable: No
Direction: Clockwise/Pulse Traveling 1500 to 1900usec
Current Drain (4.8V): 8mA/idle and 300mA no load operating
Current Drain (6.0V): 8.8mA/idle and 340mA no load operating
Dead Band Width: 8usec
Motor Type: 3 Pole Ferrite
Potentiometer Drive: Indirect Drive
Bearing Type: 1 Ball Bearing and 1 Oilite Bushing
Gear Type: Nylon
Connector Wire Length: 11.81" (300mm)
Dimensions: 1.27" x 0.66"x 1.22" (32.4 x 16.8 x 31mm)
Weight: 0.95oz (27g)

Pay Pal Welcome

Respond to this post `I'll take...!'

[TRUCKPULL]

Ken

Look at this thread

http://forums.offshoreelectrics.com/...TEC-SERVOS-MGs!

Larry

[K.R.Joye]

Prices now jive with old post, are you still interested?

[TRUCKPULL]

Hello Ken
Yes I am still interested.

Would you take $35.00 shipped to St. Catharines Ontario, Canada. for two of the 225MG's

Larry

[K.R.Joye]

No sorry, shipping cost to Canada add $4 to my asking price. Just got burned shipping there.

[TRUCKPULL]

Hello Ken

$35 + $4 = $39.00

OK??

Larry

[K.R.Joye]

That should work! Will PM my PP

[TRUCKPULL]

Hello Ken

PP -sent
Shipping address is in a PM.

Larry