Misc hardware and electronics

[lt130th]

I've acquired a few random items and parts that I'm not using. Prices do not include shipping. I'll ship USPS, with or without tracking at the discretion of the buyer, to keep total shipped price as low as possible.

#1.) SOLD Stuffing tube t-bar for 11/32 stuffing tube. Same one sold by Kintec Racing. $2.00

20150321_011207.jpg

#2.) ) SOLD Turn fin for [1/8th scale, I think] Hydro. $1.00

20150321_011605.jpg20150321_011644.jpg

#3.) ) SOLD 42mm motor ring. $1.00

20150321_011243.jpg

#4.) Jeff Wohlt .062" wire drive with 3/16" stub shaft (2.25"), and .062" to 5mm coupler with four set-screws. This was used in a Miss Geico 29 (not stock motor mount or stuffing tube length - see post #14 below) for two runs. The length of the wire from back of the stub shaft is 9.5". $15.00

20150321_005235.jpg

[lt130th]

#5.) .130" flex cable with 4mm stub shaft, drive dog, prop nut teflon liner and aluminum stuffing tube. This was pulled from a used Venom King of Shaves P1. The flex cable length from back of stub shaft is 12". $6.00

20150415_230723.jpg

#6.) LiPo voltage meter. Displays the voltage of each individual cell. $2.00

20150321_011804.jpg20150321_011757.jpg20150321_011800.jpg20150321_011811.jpg

[lt130th]

#7.) ) SOLD Aluminum mock exhaust pipes. $1.00

20150415_220238.jpg

#8.)) SOLD One rudder I know nothing about, except it's long, single-pickup and missing the cooling line fitting. $1.00

20150415_221318.jpg20150415_221207.jpg

[lt130th]

#9.) SOLD Used Pro Boat 40amp ESC with 5.5mm female bullets on the motor side. $9.00

20150415_215546.jpg20150415_215405.jpg20150415_215604.jpg

[lt130th]

#10.) ) SOLD Used 2590KV motor with .130" set-screw coupler and 50amp ESC with Deans plug. They were pulled from this Exceed 720mm mono http://www.nitrorcx.com/99b-10022-snap-720-ep-artr.html. On 3s with an x640 prop it pushed that hull between 30-40mph. Good for recovery boat, maybe. $5.00

20150415_225520.jpg20150415_225537.jpg20150415_225739.jpg20150415_230225.jpg20150415_230554.jpg

[shua]

Hello, I"ll take #1, 2, 3, 7, 8 and 10 please for $11 plus 6 for small USPS priority box?
Joshua

[lt130th]

Sure, Joshua. What is the small priority box - around $8? Can we make it an even $20 shipped?

[shua]

small priorty box should be 5.95, but I will round it up to $20 No Problem.

Funds Sent, Thanks

[royalcasa]

I've acquired a few random items and parts that I'm not using. Prices do not include shipping. I'll ship USPS, with or without tracking at the discretion of the buyer, to keep total shipped price as low as possible.


#1.) Stuffing tube t-bar for 11/32 stuffing tube. Same one sold by Kintec Racing. $2.00

[ATTACH=CONFIG]133090[/ATTACH]

#2.) Turn fin for [1/8th scale, I think] Hydro. $1.00

[ATTACH=CONFIG]133091[/ATTACH][ATTACH=CONFIG]133092[/ATTACH]

#3.) 42mm motor ring. $1.00

[ATTACH=CONFIG]133093[/ATTACH]

#4.) Jeff Wohlt .062" wire drive with 3/16" stub shaft, and .062" to 5mm coupler with four set-screws. This was used in a Miss Geico 29 for two runs. The length of the wire from back of the stub shaft is 9.5". $15.00

[ATTACH=CONFIG]133094[/ATTACH]

How long is the shaft

[lt130th]

Thank you, Joshua. I'll get everything packaged up & on its way to you, tomorrow. I'll PM you with the tracking details.

Michael P.

[lt130th]

How long is the shaft

2.25"

Thanks,
Michael P.

[royalcasa]

2.25"

Thanks,
Michael P.

Looks like it will go into my stock 29 Blackjack if so I will take it

[Sean]

If #9 still working I'll take it. Don't worry about tracking. Thanks Sean

[lt130th]

Looks like it will go into my stock 29 Blackjack if so I will take it

I don't know if there are differences between a V1 Geico 29 strut & BlackJack 29 strut, but I had to pull out the brass bushings & replace them with one of these from Kintec. I also had to turn down that shoulder about an 1/8 inch to make it go inside the strut deep enough that the end of the bushing would be flush with the end of the strut. This is all because there's not much (about 1.25") of that 2.25" left inside the strut once you have a drive dog, prop & nut on there. The stub shaft isn't really supported at all by the front strut bushing. I emailed Jeff Wohlt about this & he basically said, "yep..." Also, I modified the stuffing tube & motor location in the MG29, which consisted of moving the motor towards the transom and cutting the stuffing tube back. So the wire length might be shorter than you need for a stock BlackJack/MG 29. I should amend my description above with that info so that it isn't misleading. I don't want to be responsible for misleading anyone. Want buyers to be fully informed.

geico_bushing.jpg

[lt130th]

If #9 still working I'll take it. Don't worry about tracking. Thanks Sean

Hey, Sean. How about $12 shipped? PM inbound, with Paypal address.

Thanks,
Michael P.