Tweet
SOLD OUT - NOTHING LEFT
Mount # 1 – SOLD Three (3) Kintec Racing X-Long 2 Axis Carbon Fiber Motor Mounts. Fits 36mm or 40mm diameter motors. Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment to the stuffing tube. Multiple mounting holes for the lowest possible center of gravity. Nice large opening for thrust bearings and allows you to remove the motor without removing the collet. The adjustable tail brace allows for any length motor and up to a 70mm water jacket. The low profile makes installing and motor maintenance easier. Tail ring sold separately. Each includes an additional Axis Motor Mount Plate.
$SOLD USD each shipped to ConUS. Each additional $SOLD each shipped to same location. Take all three (3) for $SOLD USD shipped to ConUS.
Mount # 2 – SOLD on Three (3) Carbon Fiber 540XL Motor Mounts. Aluminum water cooled motor mount with carbon fiber side plates. Has rear support for L and XL motors. Tail Rings Fit 540 (36mm) sized motors. 3 5/8 inch (92mm) long.
$SOLD USD each shipped to ConUS. Each additional $SOLD each shipped to same location. Take all three (3) for $SOLD USD shipped to ConUS.
Face Plate # 1 – SOLD Water Cooled 540 Motor Mount Face Plate only. Fits 540 motors 36mm or 40mm in diameter. $SOLD USD shipped to ConUS.
Face Plate # 2 – SOLD 540 Motor Mount Face Plate only. Fits 540 motors 36mm or 40mm in diameter. $SOLD USD shipped to ConUS.
Take both Face Plates for $SOLD USD shipped to ConUS.
Tail Rings # 1 – SOLD two (2) 36mm Tail Rings. Fits motors with a 36mm diameter can. $SOLD USD each or $SOLD USD for both shipped to ConUS.
Tail Rings # 2 – SOLD two (2) 40mm Tail Rings. Fits motors with a 40mm diameter can. $SOLD USD each or $SOLD USD for both shipped to ConUS.
Mount # 1 – SOLD Three (3) Kintec Racing X-Long 2 Axis Carbon Fiber Motor Mounts. Fits 36mm or 40mm diameter motors. Made for flat bottom or deep vee installs. This motor mount allows for angular adjustment and height alignment to the stuffing tube. Multiple mounting holes for the lowest possible center of gravity. Nice large opening for thrust bearings and allows you to remove the motor without removing the collet. The adjustable tail brace allows for any length motor and up to a 70mm water jacket. The low profile makes installing and motor maintenance easier. Tail ring sold separately. Each includes an additional Axis Motor Mount Plate.
$SOLD USD each shipped to ConUS. Each additional $SOLD each shipped to same location. Take all three (3) for $SOLD USD shipped to ConUS.
Mount # 2 – SOLD on Three (3) Carbon Fiber 540XL Motor Mounts. Aluminum water cooled motor mount with carbon fiber side plates. Has rear support for L and XL motors. Tail Rings Fit 540 (36mm) sized motors. 3 5/8 inch (92mm) long.
$SOLD USD each shipped to ConUS. Each additional $SOLD each shipped to same location. Take all three (3) for $SOLD USD shipped to ConUS.
Face Plate # 1 – SOLD Water Cooled 540 Motor Mount Face Plate only. Fits 540 motors 36mm or 40mm in diameter. $SOLD USD shipped to ConUS.
Face Plate # 2 – SOLD 540 Motor Mount Face Plate only. Fits 540 motors 36mm or 40mm in diameter. $SOLD USD shipped to ConUS.
Take both Face Plates for $SOLD USD shipped to ConUS.
Tail Rings # 1 – SOLD two (2) 36mm Tail Rings. Fits motors with a 36mm diameter can. $SOLD USD each or $SOLD USD for both shipped to ConUS.
Tail Rings # 2 – SOLD two (2) 40mm Tail Rings. Fits motors with a 40mm diameter can. $SOLD USD each or $SOLD USD for both shipped to ConUS.
Comment