Tweet
Garage sale, my junk can be your junk lol! Here's a bunch of misc stuff I had laying around, I'd like to just sell it as a lot, you can part out if you want but I don't feel like dealing with it. If it doesn't sell I may break it up.......Here goes....
Speedmaster 1/4' Cat strut round bottom NIB http://www.offshoreelectrics.com/pro...-SPDS-011-250R
Speedmaster rudder transom bracket NIB SPDR-019-L
AM servo mountNIBhttp://www.offshoreelectrics.com/pro...prod=aero-6032
(2) Oct rudder standoffshttp://www.offshoreelectrics.com/pro...rod=oct-oc4off
(9) 1/4" thrust washershttp://www.offshoreelectrics.com/pro...rod=oct-oc8twm
(4) 3/16" lead teflon bushingshttp://www.offshoreelectrics.com/pro...od=oct-oc6ltsb
Aeromarine 3-piece 5mm-3/16" collet brand new but out of package, put loctite on set screw but never mountedhttp://www.offshoreelectrics.com/pro...d=aero-coupler
(1) AQ and (1) PB collets (used), 5mm-.150
transom mount water pickup new/never mounted but out of packagehttp://www.offshoreelectrics.com/pro...prod=ose-80410
Oct streamlined water pickup NIBhttp://www.offshoreelectrics.com/pro...?prod=oct-ocsw
pair of sm and pair of large rubber linkage boots, tip of 1 large has been trimmed
(4) motor coolers- (2) HRC 45mm long, one measures 40,95 inner, other is 41.15 inner, not sure what they were from. One black 60mm long for 36mm motor, not sure but I think it was on a Leo, one plastic prob from my UL-1
Leo 4074x1774kv w/cooler-FOR PARTS-not sure of wind, motor still ran, but when I noticed the melting of the wire grommet I took it apart and saw the windings were a bit dark. Assume it is bad, run at your own risk, has 8mm bullets
Giant Losi 1/5 servo-S900T, [email protected] BNIBhttp://www.losi.com/Products/Feature...rodId=LOSB0885
Modified(butchered) 3/16" stinger, I kept cutting this down experimenting, drilled to fit the flange of a shortened standard bushing, measures about 70mm from transom to tip
Impulse assembled .187 flex, looks unused, pretty sure it ishttp://www.offshoreelectrics.com/pro...e31-HD&cat=180
Impulse dual rudder kit, no transom screws/nuts or rudder breakaway bolt, pretty sure it's everything else you would need, or use it for a single rudder on a new buildhttp://www.offshoreelectrics.com/pro...rb4253&cat=180
Used UL-1 .150 flex
Prob over $250 worth of stuff, but it's an odd batch, if somebody wants it all I'll go $110 shipped in the 48 states. Bear in mind, new, the cat strut($35), AM collet($16), and the servo($50) together would cost $101... The Impulse shaft($35) and rudder setup($53) is another $88.....
Not looking for "offers" at this point. Thanks for looking.
Speedmaster 1/4' Cat strut round bottom NIB http://www.offshoreelectrics.com/pro...-SPDS-011-250R
Speedmaster rudder transom bracket NIB SPDR-019-L
AM servo mountNIBhttp://www.offshoreelectrics.com/pro...prod=aero-6032
(2) Oct rudder standoffshttp://www.offshoreelectrics.com/pro...rod=oct-oc4off
(9) 1/4" thrust washershttp://www.offshoreelectrics.com/pro...rod=oct-oc8twm
(4) 3/16" lead teflon bushingshttp://www.offshoreelectrics.com/pro...od=oct-oc6ltsb
Aeromarine 3-piece 5mm-3/16" collet brand new but out of package, put loctite on set screw but never mountedhttp://www.offshoreelectrics.com/pro...d=aero-coupler
(1) AQ and (1) PB collets (used), 5mm-.150
transom mount water pickup new/never mounted but out of packagehttp://www.offshoreelectrics.com/pro...prod=ose-80410
Oct streamlined water pickup NIBhttp://www.offshoreelectrics.com/pro...?prod=oct-ocsw
pair of sm and pair of large rubber linkage boots, tip of 1 large has been trimmed
(4) motor coolers- (2) HRC 45mm long, one measures 40,95 inner, other is 41.15 inner, not sure what they were from. One black 60mm long for 36mm motor, not sure but I think it was on a Leo, one plastic prob from my UL-1
Leo 4074x1774kv w/cooler-FOR PARTS-not sure of wind, motor still ran, but when I noticed the melting of the wire grommet I took it apart and saw the windings were a bit dark. Assume it is bad, run at your own risk, has 8mm bullets
Giant Losi 1/5 servo-S900T, [email protected] BNIBhttp://www.losi.com/Products/Feature...rodId=LOSB0885
Modified(butchered) 3/16" stinger, I kept cutting this down experimenting, drilled to fit the flange of a shortened standard bushing, measures about 70mm from transom to tip
Impulse assembled .187 flex, looks unused, pretty sure it ishttp://www.offshoreelectrics.com/pro...e31-HD&cat=180
Impulse dual rudder kit, no transom screws/nuts or rudder breakaway bolt, pretty sure it's everything else you would need, or use it for a single rudder on a new buildhttp://www.offshoreelectrics.com/pro...rb4253&cat=180
Used UL-1 .150 flex
Prob over $250 worth of stuff, but it's an odd batch, if somebody wants it all I'll go $110 shipped in the 48 states. Bear in mind, new, the cat strut($35), AM collet($16), and the servo($50) together would cost $101... The Impulse shaft($35) and rudder setup($53) is another $88.....
Not looking for "offers" at this point. Thanks for looking.
Comment