Two Savox SC-1251MG servos (low profile, high torque & fast) + extras

[lt130th]

These are used, but both are fairly new. One of the attached images is a comparison between the 1251 and a standard servo.

Dimensions(mm): 40.8X20.2X25.4
Weight(g): 44.5
Speed(@4.8V sec/60): .10
Torque(@4.8V oz-in): 97.2
Speed(@6.0V sec/60): .09
Torque(@6.0V oz-in): 125.0
Gear: Metal
Bearing: 2BB
Case: Aluminum
25 Tooth Spline
Frequency: 250-333hz
Pulse Width Frequency: 1520

http://www.savoxusa.com/Savox_SC1251MG_Digital_Servo_p/savsc1251mg.htm

Also have a Racers Edge glitch buster for any twitchy servo, and a couple of heavy duty servo arms. One is an aluminum, low profile arm, and the other is composite. They have threaded holes for ball-joint type rod ends.

Each servo is SOLD.

If anyone needs one of these arms, $2.00 each +shipping (I know the aluminum one was around $17). I can also let the glitch buster go for $2.00 +shipping if anyone wants it.

Thanks,
Michael P.

[lt130th]

20141003_231725.jpg20141003_231742.jpg20141003_232324.jpg20141003_232533.jpg

[NativePaul]

These are good servos and this is a good deal on them, I paid £50 (about $80) for my one which was also second hand.

[lt130th]

Both servos are sold (over on KBBforms.com), but the glitch buster and heavy duty servo arms are still available if anyone needs something like that.

Thanks,
Michael P.

[kfxguy]

How much for the glitch buster and the servo arm with the screw at the bottom shipped to 70706. (Hint, you can stick these in a standard envelope)

[lt130th]

How about $4.00 shipped? You mean the really low profile, aluminum arm, right?

[lt130th]

Wait...do you have a round servo arm (standard 25 tooth)?? I used to have tons of them from my RC airplane days when a transmitter came with servos and 5 different servo arms per servo. Now I can't find a single one. I must have just tossed them out years ago.

[srislash]

Wait...do you have a round servo arm (standard 25 tooth)?? I used to have tons of them from my RC airplane days when a transmitter came with servos and 5 different servo arms per servo. Now I can't find a single one. I must have just tossed them out years ago.

I can have a look for you Mike.

[lt130th]

I can have a look for you Mike.

Tiqueman sent me this nifty carbon servo arm with my Shocker, and I'd like to use it, but have no round servo arms. If postage is more than a US stamp (I'm not even sure what they're up to these days...$0.42/$0.47?) don't worry about it. I may be able to get one locally from someone. I will have to check with the airplane guys, because I have discovered only four or five people within a 100 mile radius of me that run FE boats.

20141009_174332.jpg

[kfxguy]

Tiqueman sent me this nifty carbon servo arm with my Shocker, and I'd like to use it, but have no round servo arms. If postage is more than a US stamp (I'm not even sure what they're up to these days...$0.42/$0.47?) don't worry about it. I may be able to get one locally from someone. I will have to check with the airplane guys, because I have discovered only four or five people within a 100 mile radius of me that run FE boats.

[ATTACH=CONFIG]121814[/ATTACH]

Pm me your address. I should have one. What spline do you need?

Nevermind. 25t. I should have that. It's plastic tho.....

[lt130th]

Plastic is fine. That's what I have been hunting for. If you have one, I'll send you both these servo arms and the glitch buster for $3...?