King of Shaves P-1

[Joe007]

I bought the hull from Venom. I added another layer of fiberglass to the bottom of the boat and strength the transom. I installed a turnigy H3126 1300kv outrunner with a seaking 120amp ecs with extra capacitor's I added all 6mm connectors and wired it for dual batteries, aluminum and fiberglass motor mount with cooling. I put a speedmaster stinger and brass bushing sleeve from OSE. Copper tubing for shaft. I put a Wholt's piano wire shaft with one of his steel collet. I bought the stock venom rudder assembly and I off set it . I also put stabilizer fins and turn fins on. It has a sharpen and balance octura 642 prop done by dasboata. I put a Traxxas digital water proof servo with aluminum servo mount. There is a a small blemish on the bottom of the boat that I repaired,also . There were some very small chips on the boat so I touched them up. This boat is brand new and has not been in the water or ran yet.
$500.00 plus shipping

20130701_152023.jpg20130701_152040.jpg20130701_152140.jpg20130701_152159.jpg20130701_152241.jpg.

[T3tsaya]

How long is this hull and would you be willing to sell just the hull and hardware

[Joe007]

On line they say it is 34inch but that is from the rudder. The boat is 31 inches. I do not want to part it out. If you want it I will pay the shipping.

[Scott M]

How come you built it, but never ran it?

[Joe007]

Scott I am retired and like to build and tinker. I am more of a builder than driver. Lets see I have a Hobao Hyper St Pro, Kyosho Gt and a
King of Shaves C1 and P1,BlackJack26,Stilletto that I am working on now, that I have built or modded and have not driven them. I also have a Harbor Tug, Coast Guard Rescue boat that I do run at a pond. I also have planes that sit and sit. I could go on and on.
Joe

[Scott M]

That's a nice Fleet Joe. Would be interested in a partial trade I have a 2 month old impulse 31 v2 and miss gieco 29

[Scott M]

Or I'd give 400 for it?

[Joe007]

Scott $450 and I will pay the shipping.
Joe

[Scott M]

How wide is it, what speeds would you expect from that setup and would it out run a spartan?
Thanks Joe

[T3tsaya]

If you got a bigger esc and threw on 8 cells you would probably rip the spartan in half but with a 42mm prop and 1300kv I'd say you might be at the high end of 40s or possibly low 50s but setup has everything to do with speed plus this boat could handle alot better then a spartan. This boat looks nice

[Scott M]

Could we do 430 shipped and I'll PayPal you the money today

[Joe007]

Scott it is a hair over 7 inches wide. I set the boat up for 3 or 4s packs.
I gotta get at least $450 with shipping.The seaking 120amp esc I added two more capacitors and has 5.5mm bullets on every connection. The twin bullet battery connectors would cost $13 each. Here is a picture of the esc. This boat is worth $600 easily.

[Scott M]

It's a nice boat I'm definitely interested, but I can buy a new one rtr for 429.

[Joe007]

Scott you can buy a brand new stock P1, with a 60amp esc,2000kv motor.factory servo, stock motor mount with no turn fins no water cooling to the motor can not adjust the angle on your motor once it is epoxy in
Here is mine seaking 120amp esc modded 1300kv outrunner with water cooling mount adjustaqble master strut with crossed drilled bushing for better oiling, off set rudder for better steering. turning fins. Traxxas heavy duty steel gear waterproof digital servo with aluminum servo mount. .5mm bullets. And added another layer of fiber glass to the bottom of the inside of the boat for strength .
Copper tubing not aluminum for the stuffing tube wire drive and heavy duty colect and finally the ocuta prop balanced and sharpened (brass prop balanced and sharpened cost $50)

[lowvolt]

How fast do you expect this boat to run with the current setup?