Custom Painted Revolt 30 ARTR

[dirtnsnowrider]

I am selling my custom painted (not rattle can) Revolt 30. I have an album showing the re-paint work and where it was to where it is. This Boat will come with a sharpened and balanced grim racer 42mm prop, stock 60amp esc and stock 1800kv motor. I have removed the battery tray and laid in some velcro strips to hold the batteries in place. The velcro was epoxied in to prevent lifting up. There is a secondary water pick up to allow for individual cooling of the motor and esc. The left side turn fin and mount bracket have been removed and the holes filled. The bottom of the hull has been tuned to run better. The stuff tube has been removed and re-aligned and now allows the strut to be pulled up for getting the boat to run dry. The motor has about 15 runs on it and the esc has about 25. The electronics were run with 14.8v 40c 3300-4000mah batts. The flex shaft gets the greasing after every day out to keep from rusting up. The top hatch has had an extra layer of fiberglass cloth and resin put on to strengthen it when the boat happens to flip and have impact with the water. The boat has been sanded primered and painted with nason 1 stage automotive paint. The stut has been replaced with a UL-1 strut which fits more snug than the stock one. The rudder was replaced with a Miss Vegas Deuce rudder that has a bigger water inlet hole and has been sharpened. The stock turn fin was also replaced with a SV27 turn fin for less drag in the water. Asking $200 and buyer pays shipping. Please direct all offers and questions here in the forum and not in private.

DSCN2361.jpgDSCN2371.jpgDSCN2912.jpgDSCN2925.jpgDSCN2926.jpg

[dirtnsnowrider]

DSCN2358.jpgDSCN2373.jpgDSCN2375.jpgDSCN2377.jpgDSCN2916.jpg

The revolt has the stock widow graphics applied at this time. These pics are to display the paint job and show the bottom of the hull.

[lenny]

Look nice,
What speed where you getting with it ?
Also will the boat turn left with ok with out the turn fin ?
What is your location ?

[dirtnsnowrider]

Look nice,
What speed where you getting with it ?
Also will the boat turn left with ok with out the turn fin ?
What is your location ?

The boat has been able to go mid 40's on 4s with the right prop. I use a m545 from octura. On the stock prop expect speeds around 40. I mostly ran a 120a esc/2030kv motor on 5s with a octura x440/3. I race this against a bunch of spartans on 6s and always win.

The boat turns just fine to the left. In fact I can not tell a difference in the turning.

I am in Reno NV. I have some video of it running as a trail boat in a video practice shoot.

[Speedracer128]

What speeds does hit on 5s?

[dirtnsnowrider]

What speeds does hit on 5s?

Speeds are around 46-49 mph with a 2030kv motor with a 40mm prop on 5s. Please note that the boat has the stock 60amp esc from aquacraft and a 1800kv motor in it now.

[Speedracer128]

Ok thanks for clarifying. I was misinformed about that boat. Is there a 2nd version for that boat?

I read in a couple places that with everything stock except for the prop the boat will do high 40's to low 50's. and with an upgraded esc the stock motor could handle 6s and be running in the hi 50's

[dirtnsnowrider]

Ok thanks for clarifying. I was misinformed about that boat. Is there a 2nd version for that boat?

I read in a couple places that with everything stock except for the prop the boat will do high 40's to low 50's. and with an upgraded esc the stock motor could handle 6s and be running in the hi 50's

I had swapped out motors and ran a UL-1 motor with a 120amp esc to see what speeds I could get. The 1800kv motor and 60amp esc come stock in the boat. The 1800kv motor is a stout motor and can handle being propped up to gain more speed. It can also handle the higher voltage better than the 2030kv motors. I get the same speeds with the stock set up with a M545 prop on 4s than I did when I had the UL-1 set up so back to 4s on a bigger prop and less weight = more speed. I ran this boat with a 120amp esc on 5s with the m545 prop and was doing mid 50's no problem. Hope this helps explain things a little better. The motor that comes with the boat is a 1800kv. The speed controller is the stock 60amp esc that came with it. It will come with the stock Girm Racer 42mm prop.

UPDATE: This boat has been moved to a new thread and electronics are now differnet.