Vac-U-Pickle 2S/4S Combo RTR just add prop, RX, and TX

[longballlumber]

Ok guys, I have entirely too much stuff so I am going to try this again. I have a Vac-U-Pickle that is set up to run 2S right now but I am also going to throw in another motor so you can run it with 4S also. Below is a list of what you’re getting the package deal.
Here is the original add when I was trying to sell just the hull and hardware.

http://forums.offshoreelectrics.com/...ghlight=pickle


Vac-U-Pickle hull w/hardware installed (could use a paint job)
Fullers strut and bracket
Speedmaster Mini Rudder Assy
Kintec HD turn fin bracket with GrimRacer fin installed
Several extra turn fins
3 different Hughey flex shafts (2X .150 and 1X .130 I think) Also 2X are 3/16” stub the other is 1/8” stub
Hacker 8S (with cooling jacket) – Motor hasn’t been run since a new rotor and bearings installed by Hacker
Hacker 9XL (NO cooling jacket) – Motor hasn’t been run since a new rotor and bearings installed by Hacker
Used swordfish 120 controller (Used less than 10 runs but did get a little wet so I removed the original shrink hit it with corrosionX and re-shrunk). I bench tested this morning and still works fine.
Swordfish programing box (just got this from OSE so I could sell with the boat)
Has a Hitec 225MG steering servo
REMOVED Heck – I will even throw in 2X 2S Flightpower 3700mAh packs to run it on 2S. You're not going to set any records with these, but they still charge OK and balance out just fine. REMOVED

All this for the Grand Total of $260 OBO (buyer pays actual shipping charges).

Thanks
Mike

[longballlumber]

Couple more pictures...

[Namba328]

r u willing to trade? If so what are you looking for?

[johnnywall]

Im out....building my q sport.....but this is a helluva deal for somebody!!

[longballlumber]

r u willing to trade? If so what are you looking for?

Sorry Not really interested in any trades. I am really trying to slim down my inventory of stuff I no longer run/race. Ever since out club stopped running N2 the hull hasn't seen much use.

Later,
Mike

[longballlumber]

Sorry guys, I will need to remove the batteries from the package. I cycled them a few time yesterday and they were no longer taking enough mAh's for me to justify letting someone run them. Because of this I will change the price to $260 (buyer pays actual shipping charges)...

Later,
Mike

[Jesse J]

Mike, great sale here, wish I had the funds!

If you would be willing to sell just the 8s motor, how much? I can go $50.

Thanks
J

oh, whats the KV?

[longballlumber]

Mike, great sale here, wish I had the funds!

If you would be willing to sell just the 8s motor, how much? I can go $50.

Thanks
J

oh, whats the KV?

Kv is 4613... How about $75 shipped? These motors were $200+ new and I spent more than ($75) for the new rotor and bearings?

Later,
Mike

[Jesse J]

Copy that, kv is too high for my application.
Thanks for your time,
J

[Alexgar]

Id be interested in thev.130 x1/8flexshaft

[BHChieftain]

How's the hull condition? What the transom blown out and repaired?
Also, what is the diameter of the stuffing tube?
Chief

[longballlumber]

Hey Chief,

How's the hull condition?

With regards to the hull structure I would say it's in excellent condition. The hull was joined by Phil (maker of Vac-U-Pickle hulls). The hull seam around has been sealed and looks much better (and stronger) than not filling the seam. I have also re-skinned the ride pads with 1/32" ply which also makes for nice clean (sharp) edges.

I needs a new paint job; that part looks horrible. Let's put it this way, if I repainted and "stickered" up the boat, I would be asking more money. Functionality the boat runs fine.

What the transom blown out and repaired?

In a heat race another boat flipped right infront of me and my boat went right over the top nicking the rudder (re-sharpened) and pulling the bracket away from the transom. I cut away the damaged section of the transom (the exterior ABS layer) and replaced with plywood to match thickness. This repaire was done using West Systems Epoxy 105/206. It's probably stronger than when assembled orginally. Again, as mentioned earlier needs paint. If I paint it no one would ever know there was a repair.

what is the diameter of the stuffing tube?

Stuffing tube is 1/4" (with liner) which has allowed me to successfully use .125 (.130) or .150 (all included).

Later,
Mike

If you have more questions and want to talk over the phone; PM I have no problem giving you a call and answering any questions you have.

[Alexgar]

Would you be intrested in selling the flex with the 1/8 stub?

[longballlumber]

Would you be intrested in selling the flex with the 1/8 stub?

I would rather keep it for the boat since it's cut to the correct length.

Why not just get a new one from Steven here at OSE, they are cheap? By the time you purchase mine and I charge you shipping; your more than half way to a new one.

Later,
Mike

[longballlumber]

Any reasonable offers for the entire set up before I give it away on Ebay? I need this stuff out of my shop!

Later,
Mike