Tweet
ArrowShark Dragonfly
GoTech .25 with pull start
Ofna header wrapped with Aquacrafts cooling coils
CMDi AB21ST Tuned Pipe
DuBro 6 ounce tank(I believe so)
Bow is stuffed with foam noodle
Octura .150 flex cable with 3/16 prop shaft
Engine mount is drilled for the Dyanmite .32 marine engine
Radio box was moved to the right about a half inch
comes with both JR servo mounts
DuBro quick switch mount with switch
Receiver battery mount
steering/throttle linkages with ofna horns
Aeromarine water bulkhead and Aeromarine water outlet
Speedmaster 21 rudder(un cut)
Speedmaster stinger strut
OSE 1 1/8 x 1 1/4' trim tabs
Stock turn fins
Custom exhaust tip ($$$)
K48mm prop
Large 3/16 drive dog
Octura brass bullet prop nut
Most if not all of the fasteners/screws are SS.
Boat hull needs paint! I removed all of the shady Arrowshark stickers.
Hull is white and yellow with a black cockpit window.
clear coat/paint back near the transom is starting to peal.
My guess is the oil from the nitro leaving the exhaust tip.
Transom is reinforced with a piece of 3/16" birch ply.
Ply was sealed, all stock holes were filled in the transom.
Boat was basuically rebuilt.
I bought the boat brand new from ArrowShark.
From the front of the stringers back, the hull was reinforced with
fiberglass mat and resin. Stringers were all coated with resin, at the base
and all over the sides and towards the top.
I have thought about buying a new hatch, one without the big oval
cut out of it. If you are interested, i will go ahead and pick one up and include it
with the boat. Boat was ran 4 times. Engine is still being broke in.
The electronics pictured are not included, however, We may be able
to work out some sort of deal for them.
Steering servo is a JR dz8450 and the throttle servo is a JR z9000s.
I am including a like new, Traxxas 1100mah 6v flat pack.
If the buyer would like, i will also include a like new JR Python radio
that was removed from a Shockwave 36.
The hull is stamped with an arrow shark sticker beneath the layers of
fiberglass on the inside of the hull.
i have spent several hours on this boat, i have basically lost interests for this style
of hull, i am a deep vee guy. If i run across any other items that came from or are for this
boat, i will be including them also. I am including a brand new Hitech 625mg servo if the
buyer and i do not work out a deal with the JR equipment.
Would like to get $350 for the boat.
Shipping may be additional, all depends on where you are from.
US only, lower 48 states of course.
I accept paypal and money orders.
If you have any questions, or if you are interested in the boat. Feel free to PM me.
You can also reply here.
If you would like to have a phone conversation, that is fine, simply PM me and i will
be more then happy to send you my phone number.
The hull is in great shape, it is smooth and solid.
There is 1 nick up on the nose.
This was more then likely caused during transportation.
There is also a hole in the hull towards the back of the boat.
It is pictured, the hole was sealed and is smooth with the rest
of the hull. How did it happen? Drilled to far when working on the radio box.
Here are some more pictures of the boat.
You can see the hole i was talking about towards the back of the boat.
GoTech .25 with pull start
Ofna header wrapped with Aquacrafts cooling coils
CMDi AB21ST Tuned Pipe
DuBro 6 ounce tank(I believe so)
Bow is stuffed with foam noodle
Octura .150 flex cable with 3/16 prop shaft
Engine mount is drilled for the Dyanmite .32 marine engine
Radio box was moved to the right about a half inch
comes with both JR servo mounts
DuBro quick switch mount with switch
Receiver battery mount
steering/throttle linkages with ofna horns
Aeromarine water bulkhead and Aeromarine water outlet
Speedmaster 21 rudder(un cut)
Speedmaster stinger strut
OSE 1 1/8 x 1 1/4' trim tabs
Stock turn fins
Custom exhaust tip ($$$)
K48mm prop
Large 3/16 drive dog
Octura brass bullet prop nut
Most if not all of the fasteners/screws are SS.
Boat hull needs paint! I removed all of the shady Arrowshark stickers.
Hull is white and yellow with a black cockpit window.
clear coat/paint back near the transom is starting to peal.
My guess is the oil from the nitro leaving the exhaust tip.
Transom is reinforced with a piece of 3/16" birch ply.
Ply was sealed, all stock holes were filled in the transom.
Boat was basuically rebuilt.
I bought the boat brand new from ArrowShark.
From the front of the stringers back, the hull was reinforced with
fiberglass mat and resin. Stringers were all coated with resin, at the base
and all over the sides and towards the top.
I have thought about buying a new hatch, one without the big oval
cut out of it. If you are interested, i will go ahead and pick one up and include it
with the boat. Boat was ran 4 times. Engine is still being broke in.
The electronics pictured are not included, however, We may be able
to work out some sort of deal for them.
Steering servo is a JR dz8450 and the throttle servo is a JR z9000s.
I am including a like new, Traxxas 1100mah 6v flat pack.
If the buyer would like, i will also include a like new JR Python radio
that was removed from a Shockwave 36.
The hull is stamped with an arrow shark sticker beneath the layers of
fiberglass on the inside of the hull.
i have spent several hours on this boat, i have basically lost interests for this style
of hull, i am a deep vee guy. If i run across any other items that came from or are for this
boat, i will be including them also. I am including a brand new Hitech 625mg servo if the
buyer and i do not work out a deal with the JR equipment.
Would like to get $350 for the boat.
Shipping may be additional, all depends on where you are from.
US only, lower 48 states of course.
I accept paypal and money orders.
If you have any questions, or if you are interested in the boat. Feel free to PM me.
You can also reply here.
If you would like to have a phone conversation, that is fine, simply PM me and i will
be more then happy to send you my phone number.
The hull is in great shape, it is smooth and solid.
There is 1 nick up on the nose.
This was more then likely caused during transportation.
There is also a hole in the hull towards the back of the boat.
It is pictured, the hole was sealed and is smooth with the rest
of the hull. How did it happen? Drilled to far when working on the radio box.
Here are some more pictures of the boat.
You can see the hole i was talking about towards the back of the boat.
Comment