Tweet
As my good friend said: "You have too many irons in the fire." He is right.
SOLD!!! GT-2 Conversion ALA Fine Design RC.
Wheels: White ones are cheap from China 10 min. run time. Black ones are SWEEP brand tires and were just mounted for pictures.
Spare parts are from chassis as I got it and I bought new plastic side plates and never mounted them.
There is also a tie rod kit never installed.
I never took it past 40mph (set esc to 40% max throttle limit) because after the fun of building it, going out to test it I found out it is too much of an rc car for me. Partly since I'm really only into boats and partly because I can never safely drive it being in a wheelchair. Basically I bit off more than I can drive.
I cannot get a high enough vantage point to drive it to it's max.
Since this car with a the NEU 1527 .5Y (2500KV) can do 70 mph on 2S (40C cells min!!!... I used 2S2P 25C cells) you really only need a decent 2S or 3S pack to run it up to 100 mph as claimed by Fine Design. Something like a 6000- 6700Mah 40C pack.
Car has a total of 10 minutes run time with no body on.
Body is Ipanema Warrior and Ipanema Warrior Bumper. Paint is transparent yellow backed in gold leaving a look of deep Goldish yellow metalic. For a complete newbie its a darn nice paint job and has no mileage.
Please research this setup on Fine Design's website if you are not familiar with it.
SOLD!!
POST ALL DIBS HERE AND PLEASE PAYPAL ONLY, Thank You!!
For anyone in Canada that is interested in this post your dibs here and we can work out a price if you pick up at my place or need shipping in Canada.
My loss is your gain. You can go chase a XO-1 around on less voltage and for about 1/2 the price.
Part it out and make a few bucks I don't care. Motor is still usable for a boat even though the 8mm shaft is cut down fairly short. a coupler still fits.
Lots of pictures too load... getting hungry...
SOLD!!! GT-2 Conversion ALA Fine Design RC.
Wheels: White ones are cheap from China 10 min. run time. Black ones are SWEEP brand tires and were just mounted for pictures.
Spare parts are from chassis as I got it and I bought new plastic side plates and never mounted them.
There is also a tie rod kit never installed.
I never took it past 40mph (set esc to 40% max throttle limit) because after the fun of building it, going out to test it I found out it is too much of an rc car for me. Partly since I'm really only into boats and partly because I can never safely drive it being in a wheelchair. Basically I bit off more than I can drive.
I cannot get a high enough vantage point to drive it to it's max.
Since this car with a the NEU 1527 .5Y (2500KV) can do 70 mph on 2S (40C cells min!!!... I used 2S2P 25C cells) you really only need a decent 2S or 3S pack to run it up to 100 mph as claimed by Fine Design. Something like a 6000- 6700Mah 40C pack.
Car has a total of 10 minutes run time with no body on.
Body is Ipanema Warrior and Ipanema Warrior Bumper. Paint is transparent yellow backed in gold leaving a look of deep Goldish yellow metalic. For a complete newbie its a darn nice paint job and has no mileage.
Please research this setup on Fine Design's website if you are not familiar with it.
SOLD!!
POST ALL DIBS HERE AND PLEASE PAYPAL ONLY, Thank You!!
For anyone in Canada that is interested in this post your dibs here and we can work out a price if you pick up at my place or need shipping in Canada.
My loss is your gain. You can go chase a XO-1 around on less voltage and for about 1/2 the price.
Part it out and make a few bucks I don't care. Motor is still usable for a boat even though the 8mm shaft is cut down fairly short. a coupler still fits.
Lots of pictures too load... getting hungry...
Nortavlag Bulc 
Comment