12V POWER SUPPLY 930W 77.5Amp !!!

[LiPo Power]

SOLD !!!!!

Thanks
Robert

[LiPo Power]

I will try few offers than....

[ray schrauwen]

Wow, thats one bad boy!!! Greg P might be interested in one.

How well will it operate the 400 x 2 Sky Rc charger?? http://www.hobbypartz.com/26p-ultimate800-charger.html

I hate the chargers ratings saying 11vdc - 18vdc and in the instructions they point you to the Efuel 18V 1080Watt PS I mean, the efuel is awesome but, so is this!

I've used this charger on your 47 Amp PS and it runs fine. I haven't pushed it hard yet but, not a single problem so far.

Actually the little touches you do with the switch & fan are really great!

Re: PS brackets, I don't think my machine is of the type to make it economically feasable to do the multiples you ask for. Working with thin extruded material on a mill is loud and a tad nasty.

[Brushless55]

Ray, you need about 45amps to run that charger on 12v using both ports at the same time

[LiPo Power]

Lets put it this way.
I was running this one with 4 x 4S at 10Amp each:

http://www.hobbyking.com/hobbyking/s...y_Charger.html

This one, running 4 X 2S at 5Amp each:

http://www.hobbyking.com/hobbyking/s..._Charger_.html

and 2 of this at 6Amp each on 2S:

http://www.hobbyking.com/hobbyking/s...cessories.html

All of them on the same time!!!!!

NO PROBLEM!!!!

Little heat only but if there is more heat building up I have swich installed to get X2 fan performance, just in case....

I love this puppy.....

If not sold its a keeper....

Robert

Wow, thats one bad boy!!! Greg P might be interested in one.

How well will it operate the 400 x 2 Sky Rc charger?? http://www.hobbypartz.com/26p-ultimate800-charger.html

I hate the chargers ratings saying 11vdc - 18vdc and in the instructions they point you to the Efuel 18V 1080Watt PS I mean, the efuel is awesome but, so is this!

I've used this charger on your 47 Amp PS and it runs fine. I haven't pushed it hard yet but, not a single problem so far.

Actually the little touches you do with the switch & fan are really great!

Re: PS brackets, I don't think my machine is of the type to make it economically feasable to do the multiples you ask for. Working with thin extruded material on a mill is loud and a tad nasty.

[LiPo Power]

...also Ray have a look at this:

http://forums.offshoreelectrics.com/......&highlight=

post # 2

That is the same power supply you have....

No comments.....

Wow, thats one bad boy!!! Greg P might be interested in one.

How well will it operate the 400 x 2 Sky Rc charger?? http://www.hobbypartz.com/26p-ultimate800-charger.html

I hate the chargers ratings saying 11vdc - 18vdc and in the instructions they point you to the Efuel 18V 1080Watt PS I mean, the efuel is awesome but, so is this!

I've used this charger on your 47 Amp PS and it runs fine. I haven't pushed it hard yet but, not a single problem so far.

Actually the little touches you do with the switch & fan are really great!

Re: PS brackets, I don't think my machine is of the type to make it economically feasable to do the multiples you ask for. Working with thin extruded material on a mill is loud and a tad nasty.

[LiPo Power]

Sold!!!!