FOR SALE-Brand new Pursuit W/ Leopard 4082, Traxxas WP servo, ESC, 4s 2P, + more

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • JackBlack26
    Senior Member
    • May 2007
    • 903

    #1

    FOR SALE-Brand new Pursuit W/ Leopard 4082, Traxxas WP servo, ESC, 4s 2P, + more

    Bought this last week and now need to sell it. It's never been in water.
    I ripped out everything, laid a layer of glass in it, installed a new motor mount and glassed over the battery tray and servo mount. I also installed 1/4 stuffing tube with Teflon liner and .150 cable with AQ prop shaft. It has the drive dog it came with since it's nice and beefy.

    So this is what's included:
    -Brand new Pursuit with hardware
    -Leopard 4082 2200kv motor with 4068 cooling jacket
    -Birdie 200a ESC which have had the cooling block removed, FET's sanded even, and them replaced the cooling transfer tape with silicone heat transfer paste. It has been powered up and bench tested. It has been sealed with Plastic Dip after replacing the heat shrink.
    -Turnigy BEC
    -Traxxas 2075 waterproof servo
    -Sharpened and balanced Grim Racer 42x55 prop
    -Everything has 5mm connectors on it
    --BATTERIES AND RADIO EQUIPMENT NOT INCLUDED--
    Asking price is $OLD shipped to the lower 48.

    Or $OLD shipped for hull/hardware and motor. NO ELECTRONICS OTHER THAN MOTOR




    Last edited by JackBlack26; 02-09-2012, 12:18 AM. Reason: SOLD!
  • JackBlack26
    Senior Member
    • May 2007
    • 903

    #2
    ..........................
    Last edited by JackBlack26; 02-08-2012, 05:47 PM.

    Comment

    • jeffdascanio
      Junior Member
      • Dec 2011
      • 10

      #3
      what kind of speed with that set up and lipos do you estimate it will get

      Comment

      • JackBlack26
        Senior Member
        • May 2007
        • 903

        #4
        You know, that's a good question. What I was hoping was for mid to high 30's. Probably low 40's? But I'm just guessing at this point.

        Here is one that is running the same motor on 4S with an Octura X646 3 blade and it seems to move very well. Forward to about the 6:00 mark when the guy finally shuts his mouth and puts the boat in the water.http://www.youtube.com/watch?v=5YP4sYiIOH8

        Comment

        • tlandauer
          Fast Electric Addict!
          • Apr 2011
          • 5660

          #5
          may I ask where in Calif. are you located? I am afraid of any methodof shipping, I have had no luck so far.
          Too many boats, not enough time...

          Comment

          • JackBlack26
            Senior Member
            • May 2007
            • 903

            #6
            I'm in Chino, CA. 40 minutes east of Los Angeles. Sorry to hear about your bad luck with shipping but I have yet to have one of my packages be lost or damaged. My 100% positive feedback can be found herehttp://www.rctech.net/forum/r-c-item...s-2p-more.html

            Comment

            • RCKong
              Fast Electric Addict!
              • Sep 2009
              • 1554

              #7
              I'd be surprised if you didn't see around 50mph with that setup with maybe some 30 - 40c packs

              Comment

              • JackBlack26
                Senior Member
                • May 2007
                • 903

                #8
                Thanks Kong for your input. :)

                Comment

                • tlandauer
                  Fast Electric Addict!
                  • Apr 2011
                  • 5660

                  #9
                  Thanks for your reply, I live so close ( Arcadia) but spent all my extra on something else. The boat looks sweet!
                  Too many boats, not enough time...

                  Comment

                  • JackBlack26
                    Senior Member
                    • May 2007
                    • 903

                    #10
                    Price lowered.
                    Asking price is $350 shipped to the lower 48.

                    Or $275 shipped for hull/hardware and motor. NO ELECTRONICS OTHER THAN MOTOR

                    Comment

                    • Make-a-Wake
                      FE Rules!
                      • Nov 2009
                      • 5554

                      #11
                      Yep, Kong is right on it. Mine has the same setup with 40c 4s2p running an Octura m445................runs right at 50.
                      NEED PARALLEL CONNECTORS?? QUALITY 5.5MM, 8MM, 8 AND 10 AWG, GET THEM HERE: http://forums.offshoreelectrics.com/...est!&highlight=

                      Comment

                      • jeffdascanio
                        Junior Member
                        • Dec 2011
                        • 10

                        #12
                        Like that price want to buy for 350.

                        Comment

                        • JackBlack26
                          Senior Member
                          • May 2007
                          • 903

                          #13
                          Jeff, I got your PM and returned it. Sorry, I just got back home. I lowered the price because I removed the batteries from the sale.

                          Comment

                          • rc2266
                            Senior Member
                            • Apr 2011
                            • 312

                            #14
                            What's included for 275?
                            I'm married with children, you can't scare me!

                            Comment

                            • JackBlack26
                              Senior Member
                              • May 2007
                              • 903

                              #15
                              Originally posted by rc2266
                              What's included for 275?
                              Originally posted by JackBlack26
                              Or $275 shipped for hull/hardware and motor. NO ELECTRONICS OTHER THAN MOTOR

                              Comment

                              Working...