37" Mystic Fightercat Daytona Carbon Fiber Twin Outrunner Custom Build

[VTOL]

I need confirmation............that there is zero, zero hull damage.
Thanks.

[jj2003]

Thanks for the question VTOL. Understandably so. There are some scrapes down the right side of the hull when I side swiped a wall. My opening video on my youtube channel shows the actual footage. There are no cracks or distortions in the CF. I have wet sanded the area's down with the exception of the decals which are removable and not sealed in. My plan was to replace all the decals with ones from Fightercat which match the originals, and then finish wet sanding the seams (I never did it originally) and add a final coat of two part urethane to seal it all in. I've been waiting on some materials but some issue's have come up on the home front which are forcing me to come up with some capital. Other than that, there are no other issue's. I took all this into consideration when I posted the price and deducted what I thought was a reasonable amount of money needed to bring her back to my standard's vs what I had invested into the entire build. I left out allot of little things of cost( i.e; wiring, bullet's, servo, CF mount, additional CF sheet, CF battery trays and so on) which actually amount to almost $100 but I decided to include them in the overall price because I wasn't sure if a potential buyer would keep the same setup. I hope this helps in making your decision. If you need any other photo's please feel free to ask. JJ

[VTOL]

I appreciate the response. I do understand the home front economics...............all to well.
I am also aware of the cost associated with your build.
With today's uncertainty, all purchase decision's should be weighed with as much knowledge as possible.
Will let you know.
Thanks again.

[jj2003]

Weekly Bump. Open to reasonable offers!

[74 CAT]

What was the best motor setup u listed, and what was the best speed out of that setup.

[jj2003]

What was the best motor setup u listed, and what was the best speed out of that setup.

Buyers' choice on motor's

Here's some info:

3 different motor choices

Fightercat FC3740's 1180 KV 4-12s 3000 watt
Fightercat FC3736's 1580 KV 4-6s 2700 watt
Turnigy T600's 1400 KV 5-8s 3000 watt

Fightercat 200amp HV ESC's 3-16s(max recorded was 220amp with room to spare so they are UNDERRATED at 200!)

Twin wire drive with counter-rotating 3/16 x442's.

Here's the for sale Thread

http://forums.offshoreelectrics.com/showthread.php?31514-37-quot-Mystic-Fightercat-Daytona-Carbon-Fiber-Twin-Outrunner-Custom-Build

Here's the ESC's:

http://fightercatracing.com/index.ph...mart&Itemid=59

On 6s, speeds were approaching 50mph. Watch a few of my youtube vid's from my Signature. This setup I was using Fightercat 3740's, 1180kv with 2 5000mah 3s batteries in series for 6s 5000mah. Motor's found here: http://fightercatracing.com/index.ph...emart&Itemid=1

On 10's and 12's with the 1180's, I would have been hitting 65-70. Water froze before I could test them. I have video of the test on 1180's on 12s in my youtube video's as well.

On 8s, which I didn't get to film but were GPS'ed about 55-56 mph on the 1580's found here:http://fightercatracing.com/index.ph...emart&Itemid=1.

45 MPH on Turnigy T600 1400's with 3s on each motor. Never tried on 6s or 8's with the 1400's. Motor's here:
http://www.hobbyking.com/hobbyking/store/__11980__Turnigy_T600_Brushless_Outrunner_for_600_ Heli_1400kv_.html

Here the part's list:

http://fightercatracing.com/index.php?option=com_content&view=article&id=124:f ightercat-068-carbon-fiber-twin-outrunner-cat&catid=38:fightercats-fe-project-articles&Itemid=59

[backbayboy]

Hi,

Just wanted to check from looking at the build thread the only thing not included is the 1 Flysky GT3B transmitter and receiver?
thanks.

[jj2003]

Hi,

Just wanted to check from looking at the build thread the only thing not included is the 1 Flysky GT3B transmitter and receiver?
thanks.

ARTR - No TX, RX , No camera or Batt's.

This is what's not included. Thanks.

[backbayboy]

P.M. sent

[jj2003]

PM replied.

[jj2003]

sold