Tweet
Up for sale is one of my nicer Grand Motorsport Pro Stock Brushless Drag cars,,,
She is a Awsome built Dragster!!
GMS 11 Kit#1800-$225.00 just for Roller only with stock body!!
GMS Whellie Bar assemblie with shock preloaded spring--$79.00 add on
GMS Extra Rear top plate-$24.00
GMS front foams instead of plastic skinnies-$60.00
Novak Havoc esc/13.5 brushless system with dean's connector -$169.00
Green Hemi Cuda Pro Stock body with Hood Blower-$47.00
JR steering servo JR Z270 servo with servo saver-$49.00
This Dragster is all Carbonfiber and high grade aluminum constructed,,the battery Blate and center Beam are both Thick High grade aluminum for add weight and strength against flexing,,
dont kno if you can see details in the chassis where it has alot of weight's attatched all thru the rear section on top and under chassis for Maxiumum weight transfer to the rear wheels for trction,,also brushless ESC is mounted with industial strength 3M velcro on rear plate and sit right above the brushless 13.5 motor,,the Battery tray(1/8 inche aluminum tray) sit as far back in car as possible for all wheight to get to the rear wheels,,this thing is very fast ,,I run it with a Thunderpower Pro Race 40c/80c burst lipo that packs a punch(2's)
the front has foams instead of the skinny plastic wheels and o-ring tires,,they are aluminum rims with foam tires!!
the rear foams are in still 90% tread condition if not better!!
has brand new spur gear and pinion gear also,,,
the car is completely RTR minus the RX/TX and your lipo!!!!
This car has very great potential to be a true competitior in RC drag Racing(I have a Mamba Max Pro/7700 on a 4's in it before,,it was really too insanely fast to handle,,the 13.5 is still very fast,,but you can actually control the car alot easier,,
The hemi Cuda body is in good condition,,has very,very minor cscuffs where she actuall pulled wheelie so hard she flipped over to the Driver side once,,so iI tamed her down ,,i have a smal fortune in this set up,,,
will be going on Feebay this weekend along with my other ads here on OSE,,just throwing them out here 1rst to see if the boat guys may be into dragster's in there down time on the water!!
asking $425.00 shipped plus the 3% paypal fee,,this is a steal for the price,,go to Grandmotorsports.com and see the prices for the kit,wheelie bar,extra plate,extra's,and figure in brushless system and servo and front foams,,you will see over $550.00 invested easily,,I do Usually use a taller rear foams for maximum traction and top end speed in 132ft scale quater mile,,with mamba max pro set up,,best pass in 132ft was 94mph!!!! that is in a parking lot treated with graped soda on hot pavement and Traction Compound!!
Thx for looking,,please ask for any pics you may need or any info!!!!Thx,,Bobby
She is a Awsome built Dragster!!
GMS 11 Kit#1800-$225.00 just for Roller only with stock body!!
GMS Whellie Bar assemblie with shock preloaded spring--$79.00 add on
GMS Extra Rear top plate-$24.00
GMS front foams instead of plastic skinnies-$60.00
Novak Havoc esc/13.5 brushless system with dean's connector -$169.00
Green Hemi Cuda Pro Stock body with Hood Blower-$47.00
JR steering servo JR Z270 servo with servo saver-$49.00
This Dragster is all Carbonfiber and high grade aluminum constructed,,the battery Blate and center Beam are both Thick High grade aluminum for add weight and strength against flexing,,
dont kno if you can see details in the chassis where it has alot of weight's attatched all thru the rear section on top and under chassis for Maxiumum weight transfer to the rear wheels for trction,,also brushless ESC is mounted with industial strength 3M velcro on rear plate and sit right above the brushless 13.5 motor,,the Battery tray(1/8 inche aluminum tray) sit as far back in car as possible for all wheight to get to the rear wheels,,this thing is very fast ,,I run it with a Thunderpower Pro Race 40c/80c burst lipo that packs a punch(2's)
the front has foams instead of the skinny plastic wheels and o-ring tires,,they are aluminum rims with foam tires!!
the rear foams are in still 90% tread condition if not better!!
has brand new spur gear and pinion gear also,,,
the car is completely RTR minus the RX/TX and your lipo!!!!
This car has very great potential to be a true competitior in RC drag Racing(I have a Mamba Max Pro/7700 on a 4's in it before,,it was really too insanely fast to handle,,the 13.5 is still very fast,,but you can actually control the car alot easier,,
The hemi Cuda body is in good condition,,has very,very minor cscuffs where she actuall pulled wheelie so hard she flipped over to the Driver side once,,so iI tamed her down ,,i have a smal fortune in this set up,,,
will be going on Feebay this weekend along with my other ads here on OSE,,just throwing them out here 1rst to see if the boat guys may be into dragster's in there down time on the water!!
asking $425.00 shipped plus the 3% paypal fee,,this is a steal for the price,,go to Grandmotorsports.com and see the prices for the kit,wheelie bar,extra plate,extra's,and figure in brushless system and servo and front foams,,you will see over $550.00 invested easily,,I do Usually use a taller rear foams for maximum traction and top end speed in 132ft scale quater mile,,with mamba max pro set up,,best pass in 132ft was 94mph!!!! that is in a parking lot treated with graped soda on hot pavement and Traction Compound!!
Thx for looking,,please ask for any pics you may need or any info!!!!Thx,,Bobby
Here are pics of the chassis and brushless system,,notice it is all weighted towards the end,,this is set up for competetion drag racing,,just no where locally for me too compete!! but still extremly Bad Boy car!!thx,,Bobby
Comment