Renegade Rigger RTR!!!!

[alvinsmith75]

SOLD

Hate to do it but it is time for this boat to go. I have gotten chest deep in short course racing. This boat was a blast to build and even more fun to drive. It runs like it is on rails. The boat was radard at 36mph with the plastic prop and 3s lipo. I have run it as long as 5 minutes with nothing over 120 degrees. This boat only has about 5 runs on it. It has the castle phoenix esc with pistix. I am looking to get $200.00 shipped without tx/rx. Everything else is included, including 2 3s lipos. I have an extra plastic prop and bullet propnut as well. It has 2 sets of hatches, 1 wooden and 1 lexan. The motor is the stock outrunner that comes in the kit. The boat is woodgrain and coated with epoxy. Paypal only U.S. priority mail.

[6S HYDRO]

is this a copy, it dosnt look the same dimensions as my two renegades i own.

[alvinsmith75]

No it is original. There is a build thread on here if you would like to search it. Did you build yours of buy them already assembled? You may have been sold a copy if you didn't build it yourself.
Here is the build thread minus the pics cause they have been deleted from my photobucket account. I can post the build pics later.
Alvin

[HOTWATER]

is this a copy, it dosnt look the same dimensions as my two renegades i own.

6S HYDRO...just to let you know, this Renegade is not a copy. I was in communication with Alvin when he built it.

Sorry to see it on the chop block Alvin...Very nicely built Renegade for sale here guys...

-Kent

[charlotte515]

PM sent

[alvinsmith75]

PM replied...sale pending

[alvinsmith75]

Sold

[alvinsmith75]

David your pm box is full, so here is the answer to your question......

It has traxxas connectors on it. If you use deans I suggest you swap the boat over to deans because they are much smaller and would be easier to fit in the hull. I use traxxas on everything that is why they are on there.
I don't remember the prop size but when you get it you will know because I have included an extra one still new in the package. I think the prop to get the boat over 40mph in the octura 632. If you search "renegade rigger" under the search tab you can find more than you ever wanted to know. The members were so helpful on here when I was building and had questions. You are really going to enjoy this boat. I'm not really sure why I sold it other than I haven't used it much due to racing rc cars.
Alvin

[charlotte515]

David your pm box is full, so here is the answer to your question......

It has traxxas connectors on it. If you use deans I suggest you swap the boat over to deans because they are much smaller and would be easier to fit in the hull. I use traxxas on everything that is why they are on there.
I don't remember the prop size but when you get it you will know because I have included an extra one still new in the package. I think the prop to get the boat over 40mph in the octura 632. If you search "renegade rigger" under the search tab you can find more than you ever wanted to know. The members were so helpful on here when I was building and had questions. You are really going to enjoy this boat. I'm not really sure why I sold it other than I haven't used it much due to racing rc cars.
Alvin

Thanks Alvin

[6S HYDRO]

sorry guys guess i just havnt looked at my rene's for awhile- been messin with the jap-12. they do look the same... my bad

[HOTWATER]

sorry guys guess i just havnt looked at my rene's for awhile- been messin with the jap-12. they do look the same... my bad

No worries!! I have been doing the same ...ordering parts, motor, pipe, etc.

What motor and pipe have you got for the JAE? These JAE's are a hot item right now!

-Kent

[6S HYDRO]

mines custom built from plans and modified to fit electric- bump in the tub. i have a vid in the videos section

[HOTWATER]

mines custom built from plans and modified to fit electric- bump in the tub. i have a vid in the videos section

Saw the vid...looks very good! Is it a 380 8L that you are using in it?

-Kent

[charlotte515]

R rigger

Got it today, great pack job. Really nice/quality build.

Thanks

David your pm box is full, so here is the answer to your question......

It has traxxas connectors on it. If you use deans I suggest you swap the boat over to deans because they are much smaller and would be easier to fit in the hull. I use traxxas on everything that is why they are on there.
I don't remember the prop size but when you get it you will know because I have included an extra one still new in the package. I think the prop to get the boat over 40mph in the octura 632. If you search "renegade rigger" under the search tab you can find more than you ever wanted to know. The members were so helpful on here when I was building and had questions. You are really going to enjoy this boat. I'm not really sure why I sold it other than I haven't used it much due to racing rc cars.
Alvin

[alvinsmith75]

Awesome! Enjoy.