WTB: GOOD quality 8-10 Turn Brushed 05 Can Motors

[Darin Jordan]

I am looking for a couple of good, racing quality, 05 brushed motors in the following turns:

8T
9T
10T

I may also consider a 7T motor as well...

Not looking to spend a fortune, as these won't likely get used but a couple of times...

Let me know what you have. Contact me here by PM.

Thanks,

[ray schrauwen]

I have some NEW Hughey motors never used, bought about 4 years ago. I think I have some 9T, 10T, and 11T motors, Spare armatures brushes (polarized), Springs (Polarized).

I did cut one of the 9T armature shaft down a tad... Let me see, I'll make youa really good deal.

I also do have a NIB 7T Orion Revolution Motor with those cool endbells with round brushes on an angle. Spare brushes and springs also.

So:

I have:

1)- Hughey complete motor 9T (short shaft) + 1 spare armature uncut.


1) Hughey complete motor 10T full shaft + 1 spare arm.

1) hughey 11T armature

6) POS+ brushes spare
6) NEG- brushes spare

9) brush springs not polarized.

1) Orion Revolution 7T motor NIB with many new brushes to replace and some springs I think too.

You can have the Lot shipped for $75.

Want pictures?

Paypal please.

PS, All the Hughey motors and Armatures are TRIPLE winds.

[Darin Jordan]

I have some NEW Hughey motors never used, bought about 4 years ago. I think I have some 9T, 10T, and 11T motors, Spare armatures brushes (polarized), Springs (Polarized).

I did cut one of the 9T armature shaft down a tad... Let me see, I'll make youa really good deal.

I also do have a NIB 7T Orion Revolution Motor with those cool endbells with round brushes on an angle. Spare brushes and springs also.

So:

I have:

1)- Hughey complete motor 9T (short shaft) + 1 spare armature uncut.


1) Hughey complete motor 10T full shaft + 1 spare arm.

1) hughey 11T armature

6) POS+ brushes spare
6) NEG- brushes spare

9) brush springs not polarized.

1) Orion Revolution 7T motor NIB with many new brushes to replace and some springs I think too.

You can have the Lot shipped for $75.

Want pictures?

Paypal please.

PS, All the Hughey motors and Armatures are TRIPLE winds.

Ray, Sounds good... I'll get in touch with you tomorrow to work out the deal...

I would like to see some pics... never seen a Hughey motor before... As long as they aren't Neo magnets, they'll work.

[ray schrauwen]

Pics in the morning... Night...

[ray schrauwen]

Pictures finally

[ray schrauwen]

Few more pics.

I added the Revolution endbell.

The Ed Hughey hand made motors are a Yokomo based can which he prefers because they are more accurate and consistent, just a better can than trinity.

I mention this because this extra endbell is Yokomo based also and if you just file or grind of that tiny square piece of aluminum it will fit on the Hughey cans.

I was going to use the endbell on an N1 mono stock motor but, Larry said it was illegal

[Darin Jordan]

Pictures finally

Thanks Ray... send me your PayPal address and I'll take care of payment... e-mail me directly at banzai240@yahoo.com if you don't mind...

[ray schrauwen]

Last one....

I also have a nearly new XXipp lathe from Integy. Free just pay for a bit of shipping. It's mint and tight, maybe some copper dust.

[Darin Jordan]

Ray, e-mail me with the total and the paypal address... Banzai240@Yahoo.com

Thanks!

[Darin Jordan]

PayPal sent... I like the fact that these are Hughey motors... He wasn't building them for cars!

Should work perfectly for what I want to try...

[ray schrauwen]

Shipped via canada post. tracking # sent in pm.

Thank you,

Ray

[Brushless55]

Not sure if these would work, but I have two NIB Team Orion Revoution 13x1 motors..
I was going to try them in my Revo, but they have way to much rpm for my truck..