OSE 10s rigger build

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jcald2000
    Senior Member
    • May 2008
    • 774

    #46
    Lightly cup the hopping prop near the outer edge of the blade.

    Comment

    • longballlumber
      Fast Electric Addict!
      • Apr 2007
      • 3132

      #47
      Originally posted by Steven Vaccaro
      Still dragging its tail. Seems once i get the tail out of the water it hops. Any ideas?
      Here's my 2 pennies; before bending on any props, I would try some negitive angle in the stut (prop end down). Assuming that you are currently at 0* angle (flat); it could take as little as -1* to take the hop out.

      Let us know

      Comment

      • Steven Vaccaro
        Administrator
        • Apr 2007
        • 8720

        #48
        We only ran one 2 5s packs in series. Next time out I'll run the 4 packs to make 10s2p. The weight and balance will completing change, so I'll be interested to see what happens then.
        Steven Vaccaro

        Where Racing on a Budget is a Reality!

        Comment

        • srislash
          Not there yet
          • Mar 2011
          • 7673

          #49
          That change in weight could do it alone.

          Comment

          • carlcisneros
            Fast Electric Addict!
            • Jan 2010
            • 1218

            #50
            Steve;
            drop the strut aprox. 1/8" and keep it level.
            With the ABC line of props they lift alot. keep the strut level.
            if the back end still hops, you will have to actually adjust the strut positive by just a hair
            to remove the hopping.

            If you dont like the way the boat is running after that, then switch over to a 14 or 16 series Octura prop. (still keeping the strut level)

            Comment

            • jaike5
              Senior Member
              • Dec 2011
              • 561

              #51
              Steve , I use 457 /460 / m 62x80 . 3060/8t. 10s/2p . 2 4s packs in front and 2 6s packs behind those, 5000 mah. Cheers ,Jay.

              Comment

              • jasontodd
                Junior Member
                • Feb 2013
                • 8

                #52
                nice boat steve ..also using a 2028.. what prop for 14s?? :)
                jason
                IMG_2685.jpg
                IMG_2686.jpg

                Comment

                • Steven Vaccaro
                  Administrator
                  • Apr 2007
                  • 8720

                  #53
                  Originally posted by jasontodd
                  nice boat steve ..also using a 2028.. what prop for 14s?? :)
                  jason
                  [ATTACH=CONFIG]100436[/ATTACH]
                  [ATTACH=CONFIG]100437[/ATTACH]
                  sorrry Im not sure without testing some. I would say that I dont think I would run that motor on 14s. I think 10s, or even 12s would be good. Reason I say this is that Im not sure how the magnets will hold up under that much rpm. But good like and post your results.
                  Steven Vaccaro

                  Where Racing on a Budget is a Reality!

                  Comment

                  • Fluid
                    Fast and Furious
                    • Apr 2007
                    • 8012

                    #54
                    14S is far too much for the CC2028, that's 40,000 rpm unloaded while the factory says not to exceed 30,000 rpm. Plus 40,000 is SAW territory, not for sport running or oval racing. If you want that kind of voltage, it's better to use a motor with a lower Kv. BTW you can't get NAMBA or IMPBA insurance for a 14S boat....


                    .
                    ERROR 403 - This is not the page you are looking for

                    Comment

                    • jasontodd
                      Junior Member
                      • Feb 2013
                      • 8

                      #55
                      thankyou , any updates on this 10s boat ?

                      Jason
                      Last edited by jasontodd; 07-20-2013, 08:51 AM.

                      Comment

                      Working...