What is hot and rocking at BBY

[RandyatBBY]

I REALLY like this big em effer..
looks like a real boat.

Too bad the tunnel is so small. any one know what it is? Or some info on it.

[RCNut]

Too bad the tunnel is so small. any one know what it is? Or some info on it.

I dont have a lot of info but here is a video of it running on a weed eater motor. It should go pretty good with that 2028 in it now. Maybe in a couple of weeks we can take her out for a run.

http://www.youtube.com/watch?v=OddbHfIMOUA&list=UUjwPZIU4nBUUk1CG0xf3TnQ&index=38&feature=plcp

Rich

[Brushless55]

Little more done;


Uploaded with ImageShack.us

Looks good Randy..
what powers this hull?
thanks

[RandyatBBY]

Looks good Randy..
what powers this hull?
thanks

It is set up with a UL-1 motor and esc I am setting up one with a Neu 1515 1Y for another guy. fun little 4S boat great in all weather conditions.

[RandyatBBY]

Hear is a new proto type hull I am building. Oh it is 30 inches long.


Uploaded with ImageShack.us

[Darin Jordan]

Hear is a new proto type hull I am building. Oh it is 30 inches long.


Uploaded with ImageShack.us

Randy, that's cool. What is the target power system?? Looks like a SAW boat??

[RandyatBBY]

Randy, that's cool. What is the target power system?? Looks like a SAW boat??

It is my new P Spec hydro. I lost the Skulduggery pictured below. It is at the bottom of Kaiser cove.


Uploaded with ImageShack.us

[Brushless55]

I need me a P-Spec Hydro!

[RandyatBBY]

I make three versions, kits starting at $125.00 and up. PM me with exact requirements. I will not be able to finish any ARTR's or better untill after August 2012. Hull kits and Race Basics will need to be on a rush order for the Nats.



Uploaded with ImageShack.us

[bigwaveohs]

It is my new P Spec hydro. I lost the Skulduggery pictured below. It is at the bottom of Kaiser cove.


Uploaded with ImageShack.us

Bummer...when did that happen?

[BILL OXIDEAN]

I make three versions, kits starting at $125.00 and up. PM me with exact requirements. I will not be able to finish any ARTR's or better untill after August 2012. Hull kits and Race Basics will need to be on a rush order for the Nats.



Uploaded with ImageShack.us

The new "sturgeon" Nice!

[RandyatBBY]

At the last race at Kaiser Cove Ted flipped in front of me and I could not get out of his way. I hit him and was flipped up side down. when the race was over the boat was sinking and not enough time to get to it. I lost a old pal.

[Darin Jordan]

At the last race at Kaiser Cove Ted flipped in front of me and I could not get out of his way. I hit him and was flipped up side down. when the race was over the boat was sinking and not enough time to get to it. I lost a old pal.

Randy,

It looks like you fab the sides from light-ply?? Have you ever considered doing a laminate of an inner and outter layer of 1/64th or 1/32nd ply over a some 3/32" or similar balsa, or maybe some foam-core??

It would make it super rigid, and would add some much needed floatation. If you foamed in the sponsons, and also crammed foam into the hull wherever it might fit, you may be able to keep it afloat in the worst happens.

I have pool noodle cut to fit into every available open spot on my Raptor, just in case.

[RandyatBBY]

Darin It had foam in the sponsons and pool noodles in the hull, they just sink some times. It was a real hard hit, nothing is going to help at 60MPH.

[Namba328]

Darin It had foam in the sponsons and pool noodles in the hull, they just sink some times. It was a real hard hit, nothing is going to help at 60MPH.

Exactly, I had a ovalmaster 21 set up as a p spec and during testing my bec in my esc quit and it took off full trottle accross my local pond and hit a docked paddleboat. I ended up having to get in the pond to get it but it had pool noodle stuffed in the nose and it sunk. I was lucky tho. The pond is only 6-10ft deep. Plus my lipos unplugged at impact so they didn't get hurt.