My Revolt 30 - "Bold Skull"

[gyrotron]

I need you at my pond with that rescue boat. My friend built one out of a foot long canoe he cut the back off HA.

It is not so much the rescue boat as it is the technique behind it... Mike, where do you boat?

[gyrotron]

I just ordered the x642 today from Hazegry. Meanwhile I gave some positive (up 2mm from stock setting) to the prop strut looking to rise the bow a little and try to gain some more speed. Trim tabs at 0 degrees now. I had the chine walk dialed down to a minimum when I started this thread, lets see how it behaves with the new strut setting. I will run the boat tomorrow and report back. After tomorrows's run it will be time to re-lube the prop shaft so I will be installing the thrust bearing then.

[Mike Caruso]

Cricket Creek Forest Preserve just outside of Chicago you have to get a license and be a member of IMPBA or NAMBA. I belong to the Badgers Club in WI also great bunch of people.

[gyrotron]

Cricket Creek Forest Preserve just outside of Chicago you have to get a license and be a member of IMPBA or NAMBA. I belong to the Badgers Club in WI also great bunch of people.

For some reason I thought you were in the FL area I did not pay attention to your location tag. I am not affiliated to any club yet, I just boat on a pond close by my house.

[Mike Caruso]

That would be nice I have to drive min 20 miles to run or to WI 65 miles.

[gyrotron]

That would be nice I have to drive min 20 miles to run or to WI 65 miles.

Wow 65 miles that is a trip. I like to drive but I am lucky I have this pond a couple of blocks away; you can walk around it w/o obstacles and it even has parking accross the street. I'll take a picture and post it after today's run.

Came back from today's run. Here are some pics of the pond near my house where I go boating.

[Norman2]

Hi, Gyrotron, Beware,even if you use loctite on the Bullet nut the heat from the flex shaft in the strut bushing will let the bullet nut loose and it will come off sooner or later. Do yourself
a favor. Install the normal lock nut then the bullet nut in back of it. Regards
Norman2

[gyrotron]

Hi, Gyrotron, Beware,even if you use loctite on the Bullet nut the heat from the flex shaft in the strut bushing will let the bullet nut loose and it will come off sooner or later. Do yourself
a favor. Install the normal lock nut then the bullet nut in back of it. Regards
Norman2

Yes, I have been reading not so good experiences with a bullet nut lately. I will go ahead and install a jam nut after the prop and then the bullet nut with loctite. Thanks for the advise .

[gyrotron]

Meanwhile I gave some positive (up 2mm from stock setting) to the prop strut looking to rise the bow a little and try to gain some more speed. Trim tabs at 0 degrees now. I had the chine walk dialed down to a minimum when I started this thread, lets see how it behaves with the new strut setting...

The new strut setting (+2 mm) acted negatively on the Brass Tube and Bushing. After the 5th round I started to hear a diferent motor noise and decided to stop the boat to give it a look inside. Great idea at the exact time; the brass tube was loose and bent at the section where it curbs up it had moved forward towards the collet, the teflon liner kind of started to melt, the epoxy holding the tube against the transom started to crack... it was a really bad accident starting to happen . I need some help here folks since I have never replaced a brass tube and or applied epoxy before, let me know what I need to do and how do I remove and clean up de existing epoxy to make the fix.

Do you guys think the Revolt needs an adjustable stuffing tube bracket? it is a fully adjustable bracket for 1/4 brass tube. It has adjustable height, angle and if installed with spacer washers can be adjusted side ways also. I found this piece at Kintec racing and it is used for the Motley Crew.

hhttp://kintecracing.com/Motley_Crew.html

[gyrotron]

Boat is temporarily out of the water for repairs... will probably have it ready for next weekend.

[dshuld]

Where in fl are you? Im in pinellas county.

[gyrotron]

Where in fl are you? Im in pinellas county.

Hillsborough County. Where do you boat?

[dshuld]

No where yet. Still working on my sv restoration. Taking my time on it as its my first gut and redo. The revolt is still waiting on the backer and for me to go over evrything with loctite. After reading on here for a long time finally decided to try boats. Have friend thats been trying to get me to run them at maximo park in St. Pete but its salt water.

[gyrotron]

No where yet. Still working on my sv restoration. Taking my time on it as its my first gut and redo. The revolt is still waiting on the backer and for me to go over evrything with loctite. After reading on here for a long time finally decided to try boats. Have friend thats been trying to get me to run them at maximo park in St. Pete but its salt water.

I had never heard of Maximo Park before, I just saw some pics online and it looks an interesting place for boating in salt water. Personally, I am not ready yet to run my Revolt on salt water but let us know if you do.

[dshuld]

I do t really want to either. Theres a small pond a few blocks from my apartment in gulfport on 58th st. But i havent seen anyone put a boat in so im not sure if anyone would say anything to me or not.