Replacement UL-1 arrived today....WTF?

[Ub Hauled]

I don't think anyone can blame you for that....
best of luck, at let's hope that this major company (Hobbico) gets it's act together.

[Doug Smock]

Incredible!!!!

[highndry]

Speaking of Hobby Services.

I sent back the UL 1 esc. It ran on the bench, but not in the water. Hobby Services response was that the warranty was voided because I replaced the Deans with bullet connectors ( to match my batteries). They considered this an "alteration that voided the warranty".

Beautiful.

It is abundently clear to me that Tower, Aquacraft, whoever..has no interest in supporting their product.

[Jeff Wohlt]

No, you always have to make it look factory again :)

Just about every ESC manuf says the same...as well as car ESCs, etc. Sounds stupid since the bullets are even better but they do not know the mechanics of it.

I have to say, I have not had problems with them in the past. On one car ESC when the Rev went out and it was 2 years old they sent me a new one and told me to keep the other old one. Pretty good as far as I am concerned.

This is a big issue for them with the boats since it is more than one part to replace....just think how many people are out there without a clue that bought them.

Sucks for Mike because he designed a good setup...I would be pissed if I were him and not at anyone but the manfact...especailly if hobbico gives him crap. Not his fault.

[Ub Hauled]

I had one problem with a motor/ESC from them, sent it in and a week later had the replacements...
they looked a little beaten up, although here were no marks on the motor's shaft and the bullets were new on the ESC, but they were a bit... hmm... mistreated somehow, but they work.
This in now way is an excuse to what is going on on this thread.

[alvinsmith75]

Speaking of Hobby Services.

I sent back the UL 1 esc. It ran on the bench, but not in the water. Hobby Services response was that the warranty was voided because I replaced the Deans with bullet connectors ( to match my batteries). They considered this an "alteration that voided the warranty".

Beautiful.

It is abundently clear to me that Tower, Aquacraft, whoever..has no interest in supporting their product.

I get more and more pissed off at Aquacraft/Hobby services/whomever every day after being told that I was the only one who had an esc problem!

[Doozie870]

Where are the aquacraft ramrodders from the NW now? LMAO!! Hair under the stickers? Bad hull, bad jacket, bad esc, sure to be a classic..

[skibo2]

Want to really know what is wrong with the QC and the sloppy workmanship? Look right on the box for those wonderful three little words "MADE IN CHINA." Look at all the other problems in the past few months with other products coming out of that country. I doubt very much if Hobbico has any hand in the poor quality as I don't think they would risk their reputation, however, they had better get on the backs of the manufacturer and correct the problem. As for Hobby Services, I have had three warranty issues with them, an ESC, a flex shaft and a UL-1 replacement and they were great about it no problems at all. Yes, they will deny they are not aware of problems as that is what they are told to say, if they admitted to all the issues, no one would buy their products.

[Doozie870]

Some rc products made in china are pretty good. Turnigy motors and esc's are an example.. Honestly aquacraft/grim raper/NW ramrod fools are no longer needed..

[JimClark]

Doozie if you think that aquacraft and the parent company are just sitting back and doing nothing about the problems with the boat you are very wrong. Just because they done reply to every post you make on OSE doesn't mean they are not working at repairing the issues.
They will have these issues resolved.
maybe it is you Smart Ass aditude that is not needed!
Jim Clark

[Rumdog]

True Jim, but when you call on the phone they WILL act ignorant of UL-1 issues. Besides the wwater jacket. They aren't being very helpful at all in dealing with replacement parts. Especially hulls.

[JimClark]

Not sure on the tech support have you tried to talk to supervisors?
I do know they are working on all the issues for sure

Jim

[skibo2]

I feel sorry for all of us that have lost time and money over the UL-1 QC issue but if you really want to feel sorry for people taken to the cleaners over Chinese produced inferior products you should hear what has happened here in Florida with Chinese made dry wall. During the recent hurricanes here in Fl in the past couple of years there was a dry wall shortage for the building industry and the builders purchased shiploads of dry wall from china. Well the product was manufactured with cheap material that did not measure up to spec. for water repellant and mold resistance. Now after two years in the homes the moisture has grown so much mold that the homes and business's are uninhabitable and have to be gutted or completely rebuilt to get rid of the problem and no builders warranty or manufacturers warranty to cover the cost. No insurance either so individuals have to cover repairs themselves with repair costs in the hundred of thousands of dollar ranges. So you think you have a problem? It could be a lot worst.

[Doozie870]

Thanks Jim,
One things for sure, the Grim Raper struck gold when he found your club!!

[JimClark]

Dude I am part of no club I don't even race any more and don't even have a UL-1. If I do race again it will be a scratch built boat as that is what I enjoy doing.

Jim