6 out of 10 rating on this boat. Handles great, seriously lacking quality!

[siberianhusky]

Anybody else think this boat is kinda flimsy?
Maiden run I had a blow over landed on it's back and stove in the hatch popping both of the cheezy braces off.
Motor mount allows the motor to flex up and down way to much, the flex cable is what is stopping it from moving even more.
The floor is so thin the whole stuffing tube moves up and down with the motor!
This is a fast boat with good handling but in if you compare it side by side with a Geico, the Gieco slams this thing in terms of hardware and hull quality.
Should have spent more effort building a quality hull and less on the mullet rock paint job.
I've always thought they graphics were butt ugly, but now that I've seen the lack of quality in the finish I'll be even happier to paint this thing. Bad sanding scratches under the clear coat, places where it looks like somebody smeared a finger full of putty on it and just painted over it. The clear coat is about 60 grit with all the dust in it.
To be completely honest if I bought this thing new I would have returned it instantly, the finish is that bad! Looks like a crack head chimp did the final sand, clean and paint! Above the Y in Motley on the port side there is a dimple in the finish I just can't believe QC didn't catch, looks almost like it was shot with a BB!
This will be my last Aquacraft product unless they get some of these issues under control.
I honestly would give this thing a 6 out of 10, the only reason it gets a passing grade is it handles very well.
Hardware is mid quality, has a SV27r rudder with a shorter bracket and a UL-1 strut, motor mount is a real cheap sheet metal stamping.
Good design, very cheap manufacturing.
I feel odd posting this, I bought/own the boat but really can't find that much good to say about it! Except it handles well!
I can't comment on how fast it goes with stock electronics. I have a Castle 1512 in mine with a Swordfish 120 esc. It was handling the rough water I tested it in very well, even with that power, was able to get some full throttle runs in when a SV could hardly run because of the chop.
Not the most flattering review but I think I'm being very honest about the quality of the hull and hardware, which is all I bought.

[Insaniac]

This is a trend with AQ stuff...remember the UL-1? Handled well but the hull cracked/broke a lot. I have a VS-1(wood) FE, so no complaints there...

[jeepme]

Hmmm mine is completely opposite of your description. Maybe you got a first run model or something. My finish is top notch, very smooth, and looks great IMO. Motor mount is a pretty solid aluminum mount definately not stamped steel and does flex a little foward and aft but definately not up and down. I ve submarined, flipped, landed on its lid, many times and I have been very impressed with its stregnth. Everything is holding up very well. I love my MC.

[U1Racing]

it seems that all boats in the UL-1 class crack because i have a Proboat Elam and it seems to crack just from running it in the pond, i never hit anything becaue for the hull to sustain the kind of damage that it has, you would have heard it!!

[Steven Vaccaro]

I'm son has one, I love it, he loves it.
If someone wants a shelf queen, I agree this isnt the boat.
But It does exactly what he/I wanted it to, go very fast right out of the box and handle well for a cat. It does both of those things with flying colors.
I cant find a thing wrong with the hardware.

[v-spec]

Mine was beautiful, I sold it but man was I in love with that boat. A little thicker FG woulda been nice but whatever...

[Doby]

The hardware has been proven for years on the UL1..... not sure what some people expect.

[siberianhusky]

I never faulted it handling at speed at all. It does do that very well, like I said good design.
I'm not expecting shelf queen but could they at least have dusted it off before painting it? The deck is actually gritty!
I really wish I could capture the quality of the finish in pictures. There is honestly one spot on the side of one of the steps that has a 3/32 bulge of filler right at the corner. The sponson tips look like unsanded bondo.
I will be painting this one! Amsoil style.
I said mid quality hardware which I think is fair, it's not speedmaster or anything, nothing exceptional about it, The Geico has better quality hardware.
I made it clear I couldn't give an opinion on it running against a Geico, hope to next time out, I also made it clear I couldn't comment on the motor and esc, but in a side by side comparison on the bench the Geico is a better built boat. People say this one runs better than it, I'll pass judgement on that one when I have some real life experience of the two boats running together.
So far I am very pleased with how it runs, not pleased with the overall quality. If I didn't have opportunity to compare the two I'd probably have a different opinion.
Lot of people seem to be reading things I didn't post at all, want to comment at least actually read what I posted properly!
Doby! Read my actual hardware comment again I said mid quality.

[Steven Vaccaro]

My reason for the post was this.

"6 out of 10 rating on this boat. Handles great, seriously lacking quality! "

I guess it depends on you came to a 6? As you said, you didn't have motor or esc. So you are rating the finish only.
I looked at my boat as a whole. Sure my paint has some rough spots and the sponson tips are just ok. But all in all the performance and handling are far more valuable to me than a finish.
There are PLENTY of great looking and better finished boats on the market, but what good are they if they dont turn or dont run fast?

[jeepme]

My reason for the post was this.

"6 out of 10 rating on this boat. Handles great, seriously lacking quality! "

I guess it depends on you came to a 6? As you said, you didn't have motor or esc. So you are rating the finish only.
I looked at my boat as a whole. Sure my paint has some rough spots and the sponson tips are just ok. But all in all the performance and handling are far more valuable to me than a finish.
There are PLENTY of great looking and better finished boats on the market, but what good are they if they dont turn or dont run fast?

X2. Very well said Steven. Remeber we are talking about a RTR boat. If you want perfection build a boat the way YOU want it to be. For a RTR boat this one does exactly what it was built to do........go fast and handle great, which it does perfectly.

[dana]

what do people want from a 300 dollar rtr boat? all the best hardware?!?! im mean cmon... the stuff is proven time over. yeah the paint has some issues... but really you could have read the threads, then you would have known, and not been on here bashing. just silliness

[siberianhusky]

Nope once again people are ignoring half of what I've typed! Why does everybody seem to be ignoring the fact that the hatch caved in on it's very first run? The motor flops and flexes around on it's mount ? How about the side by side comparison with the rest of the Geico hardware? Easier to ignore that I suppose as it's harder to argue with facts than opinion about a finish.

[jeepme]

Didnt you buy this boat used? Maybe the previous owner is the cause of some of the issues with the boat. I just cant see how the hatch can cave in. Like i said I have flipped and landed on the hatch more than I like to admit and its had no issues. Ive submarined it completely under water and no damage. Maybe some pics of your side by side comparison would be helpfull.

[dana]

I Agree, he bought a used boat, so it wasn't the first run. As far as motor mount? How hard is that to fix lol. And complaining about hatch quality? Try comparing to geico....Ridiculous!!!! Almost every geico made broke the flimsy hatches, so much so a forum member started making them. The geico hardware was inline and made the boat run like crap lol. But yeah that was some nice hardware lol "sarcasm". I read the whole silly rant and it's a joke

[ray schrauwen]

I just shy'ed away from AQ because the hull quality, material. I'm sure its a good handling boat but, looks and long term life are important to me in this hobby.