Bby micro hydro 50+

[BILL OXIDEAN]

Here's a vid of my record holding BBY Micro hydro in action..
Super rough out for the little tyke

Got ahold of some glass 6:30am (not in the video) she hit 63 but slammed the wall (driver error)
wasn't used to such a long freecoast after getting out of the throttle on glass..

http://www.youtube.com/watch?v=eEAtvVqG-cw

Novak Velociti 5.5r Maxamps 10,0002s2p (crammed in and the weight helps)
ETTI strut Octura x-427 Airtronics 2.4gig

[Jeff Wohlt]

Very nice. I also sell those struts with bearings and love them. I use the 4mm stepping up to 3/16" shafts.

That baby is fast! So did you total it with the wall?

[BILL OXIDEAN]

Totalled

Yessir, TOTALLED (sob sob) I really liked her. I had one almost identical hit a bouey and sink to her wattery grave never to be recovered

Yep, the drop sponsoned micro shovel is on the bench now getting hullprepped
for a direct hardware transplant.

the shovel should be exciting where I'm upping the annie to a NOVAK Ballistic series 3.5r with a 14mm rotor on the same prop.. basicly 2500 more kv

That glass run (not filmed) was incred.. I made a pass of nearly the length of the pond, and it seemed to just keep accellerating.. I got out of her too late, and that pup has NOTHING underneath it, and a little 427 has little drag/stopping power

She smooched the bank at 50+

I believe the pass to be in the mid 60's but I'll have to get the shovel built and dialed to se what's up..

These little ETTI struts are a DREAM.. bearings last forever, they spin like a turntable, needle oiler passage, sweet color..

[Jeff Wohlt]

I'm pretty sure I would not have wanted to be sitting by the wall like that girl is doing.

[BILL OXIDEAN]

I'm pretty sure I would not have wanted to be sitting by the wall like that girl is doing.

Yeah probably not the IDEAL place to spectate..
What can I say.. Adorning fans.. LoL..

[JimClark]

Bills wrecked hydro and setup pictures added











More pictures here

http://jimclark.smugmug.com/gallery/4074830_VrsAb/1/534963769_Nft7D

[Meniscus]

That's a shame Bill, sorry to hear that. Say, how is that project going with those crazy sponsons. Also, you still owe me some pictures of a certain rigger

[Jeff Wohlt]

With your speeds you might want to get out of plastic. :) I know they are strong but the weave in FG usually holds one together after the crash better.

[BILL OXIDEAN]

Hurt

Well, at that speed most any hull would have gotten hurt slamming near full speed into concrete, but indeed the little sucker would look good in composite..

[mike martin]

whats up Bill ? missed you at saws

that thing screaming

[BILL OXIDEAN]

whats up Bill ? missed you at saws

that thing screaming

Aww man, I'm done with you and Ken LoL..


You guys are too nuts crammin' 4s into a 25 inch mono..
I missed you guys too

Good job! I been meanin' to get atcha' about a few questions, gimme a call..
I was over at RCX rubbin' elbows with the sponsors, gotta' do it once a year..

I'll be down there late in the year if the guys do it, otherwise I'm lookin' at Texas
come late summer..

[BILL OXIDEAN]

Bills wrecked hydro and setup pictures added











More pictures here
http://jimclark.smugmug.com/gallery/...34963769_Nft7D

Nice job Jim!!