JAE 33FE Electric Outrigger Help

[don ferrette]

I run a Het 40mm x 2250 kv motor in my jae 33 on 4s with a 6000 mah pack, after 1 mill lap and 5 race laps the remaining capacity is at around 50% . taking into account the Het Typhoon motor is very efficient.

50%??? What prop and ESC? I tried both a Castle 1515 and now a TP 3650 at 4S and 5000mah was good for 1 mill lap and about 5 "race" laps then pack was just under 20%.

[rol243]

prop is a slightly back cut and tip cupped H7, 180 Turnigy v3 esc. hrb 6000 - 4s. esc and pack only slightly warm if that. i did start off with a castle 1414 -2400 kv motor but this just drained battery power plus made battery pack too warm as well as a t.p. 3650- 2310 kv motor same issues until i tried the Het..

[jim82]

Neu coolers fit the Het motors?

[rol243]

Thanks Jim, yes I did have trouble finding a suitable sized cooling can o rings for this motor as there no the exact 40mm diameter same as there 36 mm can is not really 36mm in diameter. RC Boat Bitz have the suitable sizes I found.

[jim82]

That's why I haven't picked one up yet because I did'nt know what cooler would work but i think i read somewhere the Neu coolers will fit. I have one on the way i just need to order the motor

[ezhitz]

I built one the end of last summer running TP 4060 1650kv on a single 6S 4500 mah limited testing it was a lot of fun to drive. I did lower the battery tray and raised the lid so the lipo would fit.

[rol243]

I built one the end of last summer running TP 4060 1650kv on a single 6S 4500 mah limited testing it was a lot of fun to drive. I did lower the battery tray and raised the lid so the lipo would fit.

looks nice and bright also like the matching stand colours.

[rol243]

Jim, the normal 36 or 40 mm cooling can sizes are fine for both sized motors its just the o-ring size you need to get right.

[RC boat addict]

Ezhitz,
I can?t view the thumbnails for some reason. I have this exact motor and a 200 amp ZTW seal esc I made my own rigger and I can?t get it to handle so I would love to see your set up and videos of it running if you have any.
What speed are you achieving ?

[RC boat addict]

Hey Raydee, I have that same motor It?s such a heavy big and powerful motor I thought the 33 might not be big enough so I built my own 36 inch rigger with bigger more buoyant sponsons much like the European p6 6s riggers but I can?t get it to handle. I am looking ahead and may have to buy either a ML boat works RSX 380 or the JRE 33 or zipkits 33. Do you have video and or photos I can view somewhere and also what speed are you achieving ?
Regards James

[Turbostang434]

I have a JAE 33. TP 4050 2100kv on 6s. 150a ESC. My boat runs in the 90s. Mph. H7 prop. Few more tweaks and I'll break 100mph.

[RC boat addict]

Since starting this post I built a 33 Fe as well I am running a 4060 1650 kv tp I have tried H7 it?s too slow probably my motors kv. The fastest speed was 1819 abc but only 79 mph 78 with 1817 having said that mine is quite heavy I am running a 200 amp Ztw esc it?s heavy the motor is heavy and my 5000mah 100 c Yowoo graphene 6s lipo is also heavy.
I would love to know your exact set up and settings.

[HTVboats]

We have a few locals who run a Q / limited class with a 4074 motor limit and a bunch of JAE 3's. With a 1750kv Lepoard and 5000ma I run a 1817/3 ABC cut down to basically a 1717 and run 6 laps in heats at 65-67mph. Doesn't sound too fast but I can pin the throttle and never lift in traffic. (till I hit a bouy) Good fun racing and a $50 Flycolor esc. I am sure with a flat out prop min 70's possible
Mic

[Turbostang434]

I'm running a Flycolor 150a ESC. With a extra cap pack I made. CNHL 5200or 6200 90c lipo with 8mm connectors for everything. H7 prop from Chris at Dasabota. I also have been getting help from Joe at zippkits. That 4060 is heavy. I'm running. 03 down on the turn fin.

[HTVboats]

I'm running a Flycolor 150a ESC. With a extra cap pack I made. CNHL 5200or 6200 90c lipo with 8mm connectors for everything. H7 prop from Chris at Dasabota. I also have been getting help from Joe at zippkits. That 4060 is heavy. I'm running. 03 down on the turn fin.

I see your in Florida. There is a one day FE race in Brandon March 27th so come out and see what were doing. Enter if you like we could use some full Q hydro's and anything else you have
Mic