Ac models boat

[Fluid]

Mine came with the “offshore” hatch from Andy.

D1D55C35-29EB-4EB0-A6B7-2852B72DFF22.jpg

[meangenesracing]

well, looks like I went and done it LOL. bought 2 1515 1650 kv motors off the forums here. just ordered 2 etti 120 hv speed controllers for my R42 hope these will push it

[srislash]

well, looks like I went and done it LOL. bought 2 1515 1650 kv motors off the forums here. just ordered 2 etti 120 hv speed controllers for my R42 hope these will push it

Congratulations Gene, so the question is, twins on the tunnel or in the sponsons?

[meangenesracing]

Congratulations Gene, so the question is, twins on the tunnel or in the sponsons?

thats a good question lol. I'm leaning toward the sponsons following your build. would you have done it differently if you could do yours over ?

[srislash]

Well the motors on the tunnel intrigues me. Andy had told me the gas guys will put the strut thru the tunnel floor and then the rudder tight to the transom. Now I knew this before my build and went my own way. It does handle great and but there is always the same ole problem with any twin having the props so far apart, they fight each other just as a posi in a car does.

I think I at some point would take a run at the tunnel mounting. It would also leave the sponsons wide open for batteries(you will have to trim the rails for better access down there BTW).

[meangenesracing]

Well the motors on the tunnel intrigues me. Andy had told me the gas guys will put the strut thru the tunnel floor and then the rudder tight to the transom. Now I knew this before my build and went my own way. It does handle great and but there is always the same ole problem with any twin having the props so far apart, they fight each other just as a posi in a car does.

I think I at some point would take a run at the tunnel mounting. It would also leave the sponsons wide open for batteries(you will have to trim the rails for better access down there BTW).

you know what , lol. I'll go with the tunnel method and let you know how it works. just maybe not the struts on the inside as I done that with my gas R42 and it was a pain to get stuffing tube in it was soooo short

[srislash]

you know what , lol. I'll go with the tunnel method and let you know how it works. just maybe not the struts on the inside as I done that with my gas R42 and it was a pain to get stuffing tube in it was soooo short

I’ve been playing with a channel mixer to remedy the posi effect but it doesn’t effect my running for the most part. If I was racing I’d be ‘on it’ more.
I look forward to your results.

[oscarel]

http://jrcbd.com/forum/showthread.php?17193-Andy-at-AC-Model-Boats-Retirement

This is a message from Andy at AC Model Boats that he wanted me to post here:

A.C. Model Boats will be making the very last shipment of boats built by Andy going at the end of May.

If you were thinking of purchasing an A.C. Boat, this would definitely be the time to get your order in.
The best way to get a hold of me is by Email at [email protected] , or you can order through Dom too.

I do want to say thank you to all my customers that have supported me over the many years of building boats.
To think I started building boats in 1979, wow 39 years.

I have made a very difficult decision, and I’m ready to retire, and pursue some other interests I have.

A.C. Boats will be up for sale, molds, jigs, the unique thing is, everything has jigs, the jigs to router all the wood components too.

The metal jigs that go into pin holes and slots, so the hull stringers and deck stringer can be pressed into the wet resin, so they can be glassed in place while still wet in the molds.

Then the molds that are hinged, A.C. Boats come out of the molds as a finished hull, Cats 100%, Mono's need the bulkhead glassed in, nothing left to do but clean up the edges, polish, pack and send off to some of the best customers in the world.

Andy
A.C. Model Boats

[srislash]

Ah geez, I New it was coming. I better give him a call, maybe I have a new career waiting.

[CraigP]

Go for it Shawn, you would build a great boat! At least look into it.

[srislash]

Go for it Shawn, you would build a great boat! At least look into it.

Yes and I’m looking at moving up Andy’s way.

[tjcast]

So where can I get my hands on one of these R-42 Cats?

[meangenesracing]

So where can I get my hands on one of these R-42 Cats?

I'll sell you mine with a Castle 2028 and etti speed control

[srislash]

Andy sold the company, it is now out of Florida. He spent two weeks with Wayne and Rick going over moulds and such. Here is their site: https://www.acmodelboats.com/cats

[jingalls007]

Wow! Andy sold the company. Good for him!

Has anyone here placed an order with the new fellas?