Prop for Titan 29

[Brushless55]

Ok, I got my Titan 29 together with a Medusa 3670 2300kv
I'm going to run in a stock class with a SV27 motor, possibly with a 45mm prop..
but with the Medusa on 4s what would be a great prop to use?
I tried a S220 and it looked to be about 45mph? I left my gps at home
any help would be great!

[Jeepers]

Brushless, a few good props to try would be x440 x640 x442 x642. are you coming down to race with us in Pueblo? By the way sweet UL1 in you avatar! I remember you telling me you did it as "Caterpillar"

[Brushless55]

yep, I am going to try and make it down there next season!

[Brushless55]

Well, I ran my Titan with a 45mm prop and jacked up the shaft...
The coupler came loose just enough to slip and melted the solder on the end of the shaft and it came unravled

[properchopper]

Ran the Titan 29/SV27 combo today with a Grim 42/55 mildly detounged & cupped.
Liked it a lot; temps were fine. More prop testing to come. What've you found ? I'm not sure the temps in a 4 min LSO race using a 445 would hold - or the 4S1P batt would like it. Get the shaft replaced & report !

[highndry]

sdgf

Proper is on the money. Additionally, Titan needs tabs with ~ 1 or 2 degrees neg trim, otherwise they are squirrely, loose & uncontrollable . At least with the following set-up, they compete favorably in our club. Ul-1 power and 440 for offshore.

[Jeepers]

were you using the Medusa or the SV27 I thought you said you were using the Medusa motor?

[Brushless55]

were you using the Medusa or the SV27 I thought you said you were using the Medusa motor?

I have yet to run the SV power, I ate a motor (SV) in my Revo that I tried one in...
I ate the shaft with the Medusa, and not sure what I need to replace it?

[Brushless55]

Ran the Titan 29/SV27 combo today with a Grim 42/55 mildly detounged & cupped.
Liked it a lot; temps were fine. More prop testing to come. What've you found ? I'm not sure the temps in a 4 min LSO race using a 445 would hold - or the 4S1P batt would like it. Get the shaft replaced & report !

Thanks!
I've not ran my Titan again, cold temps and no new shaft yet and I have no Idea what I need to replace it with...
I just got back from a run with my Revo using a Medusa 3680 1600kv and those motors are nice..

[properchopper]

Make sure you're using a .150 ! A .187 wouldn't be bad either, especially with the Medoozie. I remember a few years ago I was up North with Randy & Dan Chase doing an unofficial dual-stopwatch 2-Lap at Kaiser Cove. I had a 9XL in the Titan with a .130 & was setting a killer time, then right before the finish line - Spladoinge !! Pretzled the shaft
[BTW I just screwed up my (unsoldered end) .150 trying to insert it into the collet, then screwed up the collett Live & Learn !

[Brushless55]

Thank you and it helps to look up the add of the boat I bought!
got it all cleaned up and looks much better now
it's got a .187
http://forums.offshoreelectrics.com/...light=titan+29

[properchopper]

Just for grins here's a vid from a few years ago with a fresh 9XL on 4S2p with an
X442. Boat wasn't dialed in yet [obviously] !

http://www.youtube.com/watch?v=xW-lxKr-xxM

[Jeepers]

replace it with a Hughey .187 assembled flex shaft, available on this site under drive hardware....... darn Steve is out of stock.

[Brushless55]

replace it with a Hughey .187 assembled flex shaft, available on this site under drive hardware....... darn Steve is out of stock.

son of a

[Jeepers]

son of a

LOL!