Tweet
I have this motor in my 12th scale U-25 pay n pak on 3s and a x642 whats the max cell count I can run safely? This thing wants to take off is running flat it's just light as heck. What do i need to do?
-
-
380xl or 540xl?? 3s on 380xl max 4s on 540xl max, and thats probably too much prop i bet it will stick to the water better on something smaller -
kind of a crappy choice in kv, 3s is max i would run on that, she will roast on 4s. lol 41k on a Feigao, not gonna last more than a few runs i bet.Comment
-
Maybe 3S2P?Government Moto:
"Why fix it? Blame someone else for breaking it."Comment
-
HMM good thought dont know if I can get it in the nose. I wish I would have planned for battery compartments in the sponsons.Comment
-
You could lower the strut a bit to help keep the nose down. Unless it's true scale & has a straight shaft, that is.
If you can't fit 2 x 3s packs in there, don't be afraid to add a bit of lead ballast up the front. Just make sure it's attached well. You don't it coming loose in a high speed tumble.
Just a couple of thoughts that can work.
Paul.See the danger. THEN DO IT ANYWAY!!!
http://forums.offshoreelectrics.com/...hp?albumid=319
http://forums.offshoreelectrics.com/...hp?albumid=320Comment
-
Maybe apples and onions but I run a 540-6XL in a rigger that is good for 4-6 passes and that is on 4 cells to a 640, or 642
I assume you are after a race setup which is something I know very little about so I'll leave that to seasoned racers.
On 3S the 6xl is not a real stunner for me in a rigger but it works for you so far, so stay with it.
If you like the 3S then start with some ballast, I have had one hydro and that needed ballast to tame it down.
Once you establish your needed weight and location you may be able to go with bigger mAh packs and remove lead.
Over to you.
See it....find the photos.....sketch it it....build it........with woodComment
-
Holding world titles you can be all the master you want My friend.
I guess Ill lower the strut more.
"I assume you are after a race setup which is something I know very little about so I'll leave that to seasoned racers.
On 3S the 6xl is not a real stunner for me in a rigger but it works for you so far, so stay with it."
Seriously Simon If I could get this nose to lay flat on the water this boat would move. Its real quick at 1/4 to half throttle but if I open it up it really airs out. It turns Good i just need to make it run a little wetter.
just a note for the balsa models. Close off your turbine exhaust and the air ducts with expandable foam or somme thing coz if it flips and water catches in theses areas it will rip the hatch apart.
Oh Bill I really wish I could try a sensored novak setup in this puppy. Do the make a sensored model that would be close to this 6xl? When you get some new stuff I want dibs on a sensored setup you have.
Ill get some video on it this weekend so you can see its attitude and help me make some adjustments.
Anyone that thinks these scratch built Finlay models wont move out check this :http://www.youtube.com/watch?v=
Lastly building from scratch is so gratyfying.Last edited by TotalPackage; 04-07-2011, 05:23 PM.Comment
-
Anyone who thinks a 1/12th scale hydro wont move is a nincompoop PERIOD. I had to compete against one a few years back at the SAWS in GA it was one of the toughest battles i ever fought. Almost went home empty handed, my micro hydro Vs a 12th scale pay n pakHolding world titles you can be all the master you want My friend. I guess Ill lower the strut more.
"I assume you are after a race setup which is something I know very little about so I'll leave that to seasoned racers.
On 3S the 6xl is not a real stunner for me in a rigger but it works for you so far, so stay with it."
Seriously Simon If I could get this nose to lay flat on the water this boat would move. Its real quick at 1/4 to half throttle but if I open it up it really airs out. It turns Good i just need to make it run a little wetter.
just a note for the balsa models. Close off your turbine exhaust and the air ducts with expandable foam or somme thing coz if it flips and water catches in theses areas it will rip the hatch apart.
Oh Bill I really wish I could try a sensored novak setup in this puppy. Do the make a sensored model that would be close to this 6xl? When you get some new stuff I want dibs on a sensored setup you have.
Ill get some video on it this weekend so you can see its attitude and help me make some adjustments.
Anyone that thinks these scratch built Finlay models wont move out check this :http://www.youtube.com/watch?v=
Lastly building from scratch is so gratyfying.
We were running 19turn brushed motors on 8-cells nimh he took my record with his 48mph run, but after he packed up, I stayed and blasted through at 52..
Neat little boats, dosen't take much power to get em on flight. they were designed in the early to mid nineties when power was lacking. Lifty little sonofaguns..Comment
-
I ran a 6XL on 4s once in my Mean Machine and it was nuts!
I only got about 1min because it snapped the shaft
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
Comment
-
Comment
-
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8sComment
Comment