(retry)my brushless super hawaii project..

[Jimmy Sterling]

That bushing could do with a replacement, dont reccommend running a brushless setup in the boat with the strut in that condition, as a matter of fact I would'nt reccommend runing any motor setup in that boat with a bushing like that. Other then that I think the new thread is a good idea, I lost track of the whole project half way down the second page.

[Dr. Jet]

(wait .what? were do you see all those mistakes)

Were do I see them?

I cut and paste them from your posts.

[smm_cbf]

lookin better than last time, good job

[oldshovelhead]

looks like a good turn around on the thread and work.
keep your focus, read and reread answers to your questions.
read, reread, and reread again, then double check before you post.
good job

[Flying Scotsman]

Eclipse, I said I would not respond to your last thread. But, I see you have tidied up your act in this new thread. PLEASE review all your last 16 pages and understand people are trying to help you. All your direct drive motors and ESC choices are wrong...Ask some people who have run LARGE (36" and up) hulls on their experiences. In fact with cash being a premium, as I understand is your case. I would have left the boat as is and looked at previous threads to make the boat faster and learn how to run a boat. Next time buy a bare hull.

Douggie

[eclipse]

lol ok guys thank you.I am trying my best to understand everything .i just got some nice turn fins and my question is where to mount them??
also are those kb motors any good??they look to be an ok powerplant for the SH
post any motors that would seem good for this project(esc's also)

[eclipse]

That bushing could do with a replacement, dont reccommend running a brushless setup in the boat with the strut in that condition, as a matter of fact I would'nt reccommend runing any motor setup in that boat with a bushing like that. Other then that I think the new thread is a good idea, I lost track of the whole project half way down the second page.

dude i got that taken care of..

[Jimmy Sterling]

Good to hear, Theres a good write up on turn fins and rudders in the tips and info link on OSE's home page.

[eclipse]

cool i will look link please??
im mad i missed the pakage for all my parts today.
oh well lol

[Flying Scotsman]

lol ok guys thank you.I am trying my best to understand everything .i just got some nice turn fins and my question is where to mount them??
also are those kb motors any good??they look to be an ok powerplant for the SH
post any motors that would seem good for this project(esc's also)

Time for you to do some research...or the lads will leave you high and dry. Stop asking the same questions

I am out of here

Douggie

[eclipse]

Since I missed the delivery date from OSE here is a little update before the parts come
Pics--

Custom painted and cut boat stand with parts tray







hitec mg torque servo



2-marathon 1600mah 6-volt receiver packs customized buy taking one cell out of each and wiring them together to get 12 volts and mad into a saddle pack for cooling fan

[eclipse]

and the turn fins

[eclipse]

Time for you to do some research...or the lads will leave you high and dry. Stop asking the same questions

I am out of here

Douggie

i did i just want to hear the peoples responses
i have found this so i will go by it

http://images.google.com/imgres?imgurl=http://www.rcboataholic.com/images/hulls/turnfin-om.JPG&imgrefurl=http://www.rcboataholic.com/hardware/turnfin.htm&h=1353&w=1327&sz=73&hl=en&start=32&tbnid=B37uLpKW7CiW7M:&tbnh=150&tbnw=147&prev=/images%3Fq%3Dboat%2Bturn%2Bfins%26start%3D21%26gbv%3D2%26ndsp%3D21%26hl%3Den%26sa%3DN

[Jimmy Sterling]

The last picture of where you are holding the turn fin looks fine, Douggies got a point though, dont keep asking the same questions.

By the way what the hell does this mean ?

cool i will look link please??

[eclipse]

i meant cool..link please lol mybad